Mabs 2.28

1. Fixed a bug that was causing Mabs-flye to ignore results of the last point (the tenth point if using "--maximum_number_of_points_to_try 10"). That bug was introduced in Mabs 2.24. The bug might make some assemblies slightly worse than they could have been.
2. Since Mabs 2.24, Mabs-flye determines the option with which it gives reads to Flye, based on the median read accuracy. After a series of experiments, I decided to change the scheme that was used in Mabs 2.24. Now the Flye option depends on the median read accuracy as follows:
   (0%; 95%] - "--nano-raw"
   (95%; 99.8%] - "--nano-hq"
   (99.8%; 100%] - "--pacbio-hifi"

Mabs 2.27

1. Now Mabs-hifiasm is based on Hifiasm 0.19.8 instead of Hifiasm 0.19.5.
2. Now Mabs-flye is based on Flye 2.9.3 instead of Flye 2.9.2.
3. Several small improvements.
4. Starting from the version 2.27, Mabs is available in a Singularity container. You can download the container from https://mikeshelk.site/Diff/Mabs_distribution/Singularity_containers/ . To read about specifics of using Mabs from the container, run the command "singularity run-help mabs.sif".

Mabs 2.24

1. The optimization algorithm of Mabs-flye has been changed.
   Previously, Mabs-flye assumed the values of Flye parameters "assemble_ovlp_divergence" and "repeat_graph_ovlp_divergence" equal to each other. Mabs-flye optimized the resulting single parameter (called "max_divergence" in Mabs-flye) using the golden section method. Now Mabs-flye optimizes these two parameters independently using the Nelder-Mead method. This allows for a more thorough exploration of the parameter space.
   
   By default, Mabs-flye tests at most 10 points in the two-dimensional parameter space. One of the starting points corresponds to the default values of "assemble_ovlp_divergence" and "repeat_graph_ovlp_divergence" used by Flye.
   
   Less than 10 points may be tested if the optimization algorithm (the function scipy.optimize.minimize of the Python library SciPy) desides that convergence has been achieved.
   
   The maximum number of tried points can be set with a new Mabs-flye parameter "--maximum_number_of_points_to_try". Increasing the value of this parameter will increase the computation time of Mabs-flye, but may make the assembly better. By default, the value of "--maximum_number_of_points_to_try" is 10.
   

2. The optimization algorithm of Mabs-hifiasm has been changed.
   Previously, if two "-s" values of Hifiasm led in the same AG, Mabs-hifiasm considered the assembly with the smaller "-s" better (smaller "-s" corresponds to stricter pruning of possible haplotypic duplications). Now if two "-s" values lead to the same AG, Mabs-hifiasm considers the best the one whose assembly has the larger N50. If both assemblies have the same N50 then, as previously, the assembly with the smaller "-s" is preferred.
   

3. Previously, Mabs-flye provided all reads to Flye via the option "--nano-raw". Now, Mabs-flye uses the Phred score lines in FASTQ to calculate the accuracy of each read. Then, Mabs-flye calculates the median accuracy among all reads.
   The correspondence between the median accuracy and the option with which Mabs-flye provides reads to Flye:
   (0%; 95%] - "--nano-raw"
   (95%; 97%] - "--nano-hq"
   (97%; 99%] - "--nano-corr"
   (99%; 100%] - "--pacbio-hifi"
   
   To speed up the read accuracy calculation, Mabs-flye calculates the accuracy only for BUSCO reads (i.e. reads that correspond to BUSCO genes).
   

4. Now Mabs-hifiasm is based on Hifiasm 0.19.5 instead of Hifiasm 0.19.3.
   

5. Several small changes in names of subfolders and files produced by Mabs have been made.
   

6. Several bugs which slightly decreased the assembly accuracy have been fixed.

Mabs 2.19

Fixed a small bug that prevented calculate_AG from downloading BUSCO datasets.

Mabs 2.18

1. Now Mabs-flye is based on Flye 2.9.2 instead of Flye 2.9.1. This may increase the assembly quality.
2. Now Mabs-hifiasm is based on Hifiasm 0.19.3 instead of Hifiasm 0.16.1. This may increase the assembly quality.
3. The ability to use ultralong Nanopore reads has been recently added to Hifiasm. Mabs-hifiasm now can use them too, via a new option "--ultralong-nanopore-reads".
4. A new option "--additional_flye_parameters" has been added to Mabs-flye. A user can pass some Flye-specific parameters to Flye through it.
5. A new option "--additional_hifiasm_parameters" has been added to Mabs-hifiasm. A user can pass some Hifiasm-specific parameters to Hifiasm through it.
6. Several small improvements.

Mabs 2.14

Now Mabs does not use Git LFS, which is a method used by Git to store large files. This may fix some issues with installation of Mabs.

Mabs 2.13

Made several changes in the output of "mabs-flye.py --help" and "calculate_AG.py --help".

Mabs 2.12

Now Mabs stops if the output folder already exists and is not empty.

Mabs 2.11

The first version of Mabs uploaded to GitHub.