Merge pull request #37 from bolek2000/master

Add FSP__Custos9X+_CU-1102TS__nutdrv_qx__2.7.4__01.dev file

FSP/FSP__Custos9X+_CU-1102TS__nutdrv_qx__2.7.4__01.dev

@@ -0,0 +1,159 @@
+# Please add if relevant: DEVICE:URL:REPORT: <GitHub issue/PR or Mailing list archive entry URL>
+# Please add if relevant: DEVICE:URL:VENDOR: https://fsp-ps.de/en/product/ups/1489361476-415.html
+
+# Please add comments for humans here and perhaps raise concerns about the data points,
+# see https://networkupstools.org/ddl/#devseq-files for comment-tag syntax
+# strip sensitive data (passwords, SNMP community, serial number, IP address, host name...)
+# and post as a pull request to https://github.com/networkupstools/nut-ddl/
+# DEVICE:COMMENT:
+# Device dump generated by ./nut-ddl-dump.sh on Tue, 12 Sep 2023 15:28:27 +0200
+# DEVICE:EOC
+
+# :; upsc fsp
+battery.charge: 100
+battery.energysave: no
+battery.packs: 1
+battery.protection: yes
+battery.runtime: 180
+battery.voltage: 54.70
+battery.voltage.nominal: 48.0
+device.model: XIIHVT2K0
+device.serial: 12345678901234
+device.type: ups
+driver.name: nutdrv_qx
+driver.parameter.bus: 001
+driver.parameter.pollfreq: 30
+driver.parameter.pollinterval: 2
+driver.parameter.port: auto
+driver.parameter.productid: 5161
+driver.parameter.synchronous: no
+driver.parameter.vendorid: 0665
+driver.version: 2.7.4
+driver.version.data: Voltronic 0.06
+driver.version.internal: 0.28
+input.current.nominal: 8.0
+input.frequency: 50.0
+input.frequency.high: 53.0
+input.frequency.low: 47.0
+input.frequency.nominal: 50.0
+input.phases: 1
+input.transfer.high: 242
+input.transfer.high.max: 254
+input.transfer.high.min: 237
+input.transfer.low: 218
+input.transfer.low.max: 223
+input.transfer.low.min: 206
+input.voltage: 239.4
+input.voltage.nominal: 230.0
+outlet.0.switchable: no
+output.current: 0.0
+output.current.nominal: 8
+output.frequency: 0.0
+output.frequency.nominal: 50.0
+output.phases: 1
+output.power.maximum.percent: 1
+output.power.minimum.percent: 1
+output.powerfactor: 0.9
+output.voltage: 0.0
+output.voltage.nominal: 230.0
+ups.beeper.status: enabled
+ups.delay.shutdown: 30
+ups.delay.start: 180
+ups.firmware: 01359.08
+ups.firmware.aux: P01
+ups.load: 0
+ups.power.nominal: 2000
+ups.productid: 5161
+ups.start.auto: yes
+ups.start.battery: yes
+ups.status: OL OFF
+ups.temperature: 26.5
+ups.type: online
+ups.vendorid: 0665
+
+# DEVICE:COMMENT-BLOCK:FIXME:UPSRW: fsp
+# [battery.energysave]
+# Switch off when running on battery and no/low load
+# Type: ENUM
+# Option: "no" SELECTED
+# Option: "yes"
+#
+# [battery.packs]
+# Number of battery packs
+# Type: RANGE
+# Option: "1-99" SELECTED
+#
+# [battery.protection]
+# Prevent deep discharge of battery
+# Type: ENUM
+# Option: "no"
+# Option: "yes" SELECTED
+#
+# [input.frequency.high]
+# Maximum input line frequency (Hz)
+# Type: RANGE
+# Option: "53-60" SELECTED
+#
+# [input.frequency.low]
+# Minimum input line frequency (Hz)
+# Type: RANGE
+# Option: "40-47" SELECTED
+#
+# [input.transfer.high]
+# High voltage transfer point (V)
+# Type: RANGE
+# Option: "237-254" SELECTED
+#
+# [input.transfer.low]
+# Low voltage transfer point (V)
+# Type: RANGE
+# Option: "206-223" SELECTED
+#
+# [outlet.0.switchable]
+# Description unavailable
+# Type: ENUM
+# Option: "no" SELECTED
+# Option: "yes"
+#
+# [ups.delay.shutdown]
+# Interval to wait after shutdown with delay command (seconds)
+# Type: RANGE
+# Option: "12-5940" SELECTED
+#
+# [ups.delay.start]
+# Interval to wait before (re)starting the load (seconds)
+# Type: RANGE
+# Option: "0-599940" SELECTED
+#
+# [ups.start.auto]
+# UPS starts when mains is (re)applied
+# Type: ENUM
+# Option: "no"
+# Option: "yes" SELECTED
+#
+# [ups.start.battery]
+# Allow to start UPS from battery
+# Type: ENUM
+# Option: "no"
+# Option: "yes" SELECTED
+# DEVICE:EOC
+
+# DEVICE:COMMENT-BLOCK:FIXME:UPSCMD: fsp
+# Instant commands supported on UPS [fsp]:
+#
+# beeper.disable - Disable the UPS beeper
+# beeper.enable - Enable the UPS beeper
+# beeper.toggle - Toggle the UPS beeper
+# bypass.start - Put the UPS in bypass mode
+# bypass.stop - Take the UPS out of bypass mode
+# load.off - Turn off the load immediately
+# load.on - Turn on the load immediately
+# shutdown.return - Turn off the load and return when power is back
+# shutdown.stayoff - Turn off the load and remain off
+# shutdown.stop - Stop a shutdown in progress
+# test.battery.start - Start a battery test
+# test.battery.start.deep - Start a deep battery test
+# test.battery.start.quick - Start a quick battery test
+# test.battery.stop - Stop the battery test
+# DEVICE:EOC
+