[New component] HiFiBerry Sound Card & OnOff SHIM

documentation/builders/README.md

@@ -14,6 +14,12 @@
 * [Card Database](./card-database.md)
 * [Troubleshooting](./troubleshooting.md)
 
+## Components
+* [Power](./components/power/)
+    * [OnOff SHIM for safe power on/off](./components/power/onoff-shim.md)
+* [Soundcards](./components/soundcards/)
+    * [HiFiBerry Boards](./components/soundcards/hifiberry.md)
+
 ## Advanced
 
 * [Bluetooth (and audio buttons)](./bluetooth-audio-buttons.md)

documentation/builders/components/power/onoff-shim.md

@@ -0,0 +1,34 @@
+# OnOff SHIM by Pimorino
+
+The OnOff SHIM from Pimorino allows you to savely start and shutdown your Raspberry Pi through a button. While you can switch of your Phoniebox via an RFID Card (through an RPC command), it is difficult to switch it on again without cutting the physical power supply.
+
+## Installation
+
+To install the software, open a terminal and type the following command to run the one-line-installer. A reboot will be required once the installation is finished.
+
+> [!NOTE]
+> The installations will ask you a few questions. You can safely answer with the default response.
+
+```
+curl https://get.pimoroni.com/onoffshim | bash
+```
+
+* [Source](https://shop.pimoroni.com/products/onoff-shim?variant=41102600138)
+
+## How to manually wire OnOff SHIM
+
+The OnOff SHIM comes with a 12-PIN header which needs soldering. If you want to spare some GPIO pins for other purposes, you can individually wire the OnOff SHIM with the Raspberry Pi. Below you can find a table of Pins to be connected.
+
+| Board pin name | Board pin | Physical RPi pin | RPi pin name |
+|----------------|-----------|------------------|--------------|
+| 3.3V           | 1         | 1, 17            | 3V3 power    |
+| 5V             | 2         | 2                | 5V power     |
+| 5V             | 4         | 4                | 5V power     |
+| GND            | 6         | 6, 9, 20, 25     | Ground       |
+| GPLCLK0        | 7         | 7                | GPIO4        |
+| GPIO17         | 11        | 11               | GPIO17       |
+
+## Assembly options
+
+![](https://cdn.review-images.pimoroni.com/upload-b6276a310ccfbeae93a2d13ec19ab83b-1617096824.jpg?width=640)
+

documentation/builders/components/soundcards/hifiberry.md

@@ -0,0 +1,49 @@
+# HiFiBerry
+
+The installation script works for the most common set of HiFiBerry boards but also other "DAC" related sound cards like `I2S PCM5102A DAC`.
+
+## Automatic setup
+
+Run the following command to install any HiFiBerry board. Make sure you reboot your device afterwards.
+
+```
+cd; cd ~/RPi-Jukebox-RFID/installation/components && chmod +x setup_hifiberry.sh
+./setup_hifiberry.sh
+```
+
+If you know you HifiBerry Board identifier, you can run the script as a 1-liner as well
+
+```
+./setup_hifiberry.sh enable hifiberry-dac
+```
+
+If you like to disable your HiFiberry Sound card and enable onboard sound, run the folliwing command
+
+
+```
+./setup_hifiberry.sh disable
+```
+
+## Additional information
+
+If you like to understand what's happening under the hood, feel free to check the [install script](../../../../installation/components/setup_hifiberry.sh).
+
+The setup is based on [HiFiBerry's instructions](https://www.hifiberry.com/docs/software/configuring-linux-3-18-x/).
+
+## How to manually wire your HiFiBerry board
+
+Most HiFiBerry boards come with 40-pin header that you can directly attach to your Pi. This idles many GPIO pins that may be required for other inputs to be attached (like GPIO buttons or RFID). You can also connect your HiFiBerry board separately. The following table show cases the pins required.
+
+* [Raspberry Pi Pinout](https://github.com/raspberrypi/documentation/blob/develop/documentation/asciidoc/computers/os/using-gpio.adoc)
+
+| Board pin name | Board pin | Physical RPi pin | RPi pin name |
+|----------------|-----------|------------------|--------------|
+| 3.3V           | 1         | 1, 17            | 3V3 power    |
+| 5V             | 2         | 2, 4             | 5V power     |
+| GND            | 6         | 6, 9, 20, 25     | Ground       |
+| PCM_CLK        | 12        | 12               | GPIO18       |
+| PCM_FS         | 36        | 36               | GPIO19       |
+| PCM_DIN        | 38        | 38               | GPIO20       |
+| PCM_DOUT       | 40        | 40               | GPIO21       |
+
+You can find more information about manually wiring [here](https://forum-raspberrypi.de/forum/thread/44967-kein-ton-ueber-hifiberry-miniamp-am-rpi-4/?postID=401305#post401305).

installation/components/setup_hifiberry.sh

@@ -0,0 +1,119 @@
+#!/usr/bin/env bash
+
+# This script follows the official HiFiBerry documentation
+# https://www.hifiberry.com/docs/software/configuring-linux-3-18-x/
+
+source ../includes/02_helpers.sh
+
+script_name=$(basename "$0")
+boot_config_path=$(get_boot_config_path)
+
+declare -A hifiberry_map=(
+    ["hifiberry-dac"]="DAC (HiFiBerry MiniAmp, I2S PCM5102A DAC)"
+    ["hifiberry-dacplus"]="HiFiBerry DAC+ Standard/Pro/Amp2"
+    ["hifiberry-dacplushd"]="HiFiBerry DAC2 HD"
+    ["hifiberry-dacplusadc"]="HiFiBerry DAC+ ADC"
+    ["hifiberry-dacplusadcpro"]="HiFiBerry DAC+ ADC Pro"
+    ["hifiberry-digi"]="HiFiBerry Digi+"
+    ["hifiberry-digi-pro"]="HiFiBerry Digi+ Pro"
+    ["hifiberry-amp"]="HiFiBerry Amp+ (not Amp2)"
+    ["hifiberry-amp3"]="HiFiBerry Amp3"
+)
+
+example_usage() {
+    for key in "${!hifiberry_map[@]}"; do
+        description="${hifiberry_map[$key]}"
+        echo "$key) $description"
+    done
+    echo "Example usage: ./${script_name} enable hifiberry-dac"
+}
+
+enable_hifiberry() {
+    echo "Enabling HiFiBerry board..."
+    grep -qxF "dtoverlay=$1" "$boot_config_path" || echo "dtoverlay=$1" | sudo tee -a "$boot_config_path" > /dev/null
+    ./../options/onboard_sound.sh disable
+}
+
+disable_hifiberry() {
+    echo "Removing existing HiFiBerry configuration..."
+    sudo sed -i '/dtoverlay=hifiberry-/d' "$boot_config_path"
+    ./../options/onboard_sound.sh enable
+}
+
+check_existing_hifiberry() {
+    existing_config=$(grep 'dtoverlay=hifiberry-' "$boot_config_path")
+    if [ ! -z "$existing_config" ]; then
+        if [ "$1" = "silent" ]; then
+            disable_hifiberry
+            return 0
+        fi
+
+        echo "Existing HiFiBerry configuration detected: $existing_config"
+        read -p "Do you want to proceed with a new configuration? This will remove the existing one. (Y/n): " choice
+        case $choice in
+            [nN][oO]|[nN])
+                echo "Exiting without making changes.";
+                exit;;
+            *)
+                disable_hifiberry;
+                return 0;;
+        esac
+    fi
+}
+
+# 1-line installation
+if [ $# -ge 1 ]; then
+    if [[ "$1" != "enable" && "$1" != "disable" ]] || [[ "$1" == "enable" && -z "$2" ]]; then
+        echo "Error: Invalid arguments provided.
+Usage: ./${script_name} <status> <hifiberry-board>
+where <status> can be 'enable' or 'disable'.
+
+The following board options exist:"
+        example_usage
+        exit 1
+    fi
+
+    if [ "$1" == "enable" ]; then
+        if [[ -v hifiberry_map["$2"] ]]; then
+            check_existing_hifiberry "silent"
+            enable_hifiberry "$2"
+            exit 1
+        fi
+
+        echo "'$2' is not a valid option. You can choose from:"
+        example_usage
+        exit 1
+    fi
+
+    disable_hifiberry
+    exit 1
+fi
+
+# Guided installation
+board_count=${#hifiberry_map[@]}
+counter=1
+
+echo "Select your HiFiBerry board:"
+for key in "${!hifiberry_map[@]}"; do
+    description="${hifiberry_map[$key]}"
+    echo "$counter) $description"
+    ((counter++))
+done
+echo "0) Remove existing HiFiBerry configuration"
+
+read -p "Enter your choice (0-$board_count): " choice
+case $choice in
+    [0])
+        disable_hifiberry;
+        ;;
+    [1-$board_count])
+        check_existing_hifiberry
+        selected_board=$(get_key_by_item_number hifiberry_map "$choice")
+        enable_hifiberry "$selected_board";
+        ;;
+    *)
+        echo "Invalid selection. Exiting.";
+        exit 1;;
+esac
+
+echo "Configuration complete. Please restart your device."

installation/includes/02_helpers.sh

@@ -2,6 +2,21 @@
 
 ### Helpers
 
+# Get key by item number of associated array
+get_key_by_item_number() {
+    local -n array="$1"
+    local item_number="$2"
+    local count=0
+
+    for key in "${!array[@]}"; do
+        ((count++))
+        if [ "$count" -eq "$item_number" ]; then
+            echo "$key"
+            return
+        fi
+    done
+}
+
 # $1->start, $2->end
 calc_runtime_and_print() {
   runtime=$(($2-$1))
@@ -35,18 +50,57 @@ run_with_log_frame() {
 }
 
 get_architecture() {
-  local arch=""
-  if [ "$(uname -m)" = "armv7l" ]; then
-    arch="armv7"
-  elif [ "$(uname -m)" = "armv6l" ]; then
-    arch="armv6"
-  elif [ "$(uname -m)" = "aarch64" ]; then
-    arch="arm64"
-  else
-    arch="$(uname -m)"
-  fi
-
-  echo $arch
+    local arch=""
+    if [ "$(uname -m)" = "armv7l" ]; then
+        arch="armv7"
+    elif [ "$(uname -m)" = "armv6l" ]; then
+        arch="armv6"
+    elif [ "$(uname -m)" = "aarch64" ]; then
+        arch="arm64"
+    else
+        arch="$(uname -m)"
+    fi
+
+    echo $arch
+}
+
+is_raspian() {
+    if [[ $( . /etc/os-release; printf '%s\n' "$ID"; ) == *"raspbian"* ]]; then
+        echo true
+    else
+        echo false
+    fi
+}
+
+get_debian_version() {
+    # Read the major version number from /etc/debian_version
+    local major_version="$( . /etc/os-release; printf '%s\n' "$VERSION_CODENAME"; )"
+
+    case $major_version in
+        11)
+            echo "bullseye"
+            ;;
+        12)
+            echo "bookworm"
+            ;;
+        *)
+            echo "unknown"
+            ;;
+    esac
+}
+
+get_boot_config_path() {
+    if [ "$(is_raspian)" = true ]; then
+        local debian_version=$(get_debian_version)
+
+        if [ "$debian_version" = "bookworm" ]; then
+            echo "/boot/firmware/config.txt"
+        else
+            echo "/boot/config.txt"
+        fi
+    else
+        echo "unknown"
+    fi
 }
 
 validate_url() {

installation/options/onboard_sound.sh

@@ -0,0 +1,32 @@
+#!/usr/bin/env bash
+source ../includes/02_helpers.sh
+script_name=$(basename "$0")
+boot_config_path=$(get_boot_config_path)
+
+if [ -z "$1" ] || { [ "$1" != "enable" ] && [ "$1" != "disable" ]; }; then
+    echo "Error: Invalid or no argument provided.
+Usage: ./${script_name} <arg>
+       where <arg> can be 'enable' or 'disable'"
+    exit 1
+fi
+
+arg="$1"
+
+if [ "$arg" = "enable" ]; then
+    echo "Enabling Onboard Sound..."
+    sudo sed -i '/dtoverlay=vc4-fkms-v3d,audio=off/c\dtoverlay=vc4-fkms-v3d' "$boot_config_path"
+    sudo sed -i '/dtoverlay=vc4-kms-v3d,noaudio/c\dtoverlay=vc4-kms-v3d' "$boot_config_path"
+elif [ "$arg" = "disable" ]; then
+    echo "Disabling Onboard Sound..."
+    sudo sed -i "s/^\(dtparam=\([^,]*,\)*\)audio=\(on\|true\|yes\|1\)\(.*\)/\1audio=off\4/g" "$boot_config_path"
+
+    if grep -qx 'dtoverlay=vc4-fkms-v3d' "$boot_config_path"; then
+        sudo sed -i '/dtoverlay=vc4-fkms-v3d/c\dtoverlay=vc4-fkms-v3d,audio=off' "$boot_config_path"
+    fi
+
+    if grep -qx 'dtoverlay=vc4-kms-v3d' "$boot_config_path"; then
+        sudo sed -i '/dtoverlay=vc4-kms-v3d/c\dtoverlay=vc4-kms-v3d,noaudio' "$boot_config_path"
+    fi
+fi
+
+# TODO Test