Update some datasheets with new fw0.7 options

source/Hardware Guide/Datasheets/ds90ub9x-raw.rst

@@ -54,7 +54,11 @@ Managed register access is provided at offset 0x8000.
       - On Reset
       - 1280
       - None
-      - Frame data size in samples
+      - Amount of data to read into a frame
+
+        * Bits 0-15: In parallel mode: frame data size in samples. 
+          In serial mode: Number of words per frame in each line.
+        * Bits 16-31: Number of frames to aggregate. 0 = do not perform aggregation
 
     * - 0x8002
       - TRIGGER
@@ -103,7 +107,7 @@ Managed register access is provided at offset 0x8000.
         * 0x1: included
 
     * - 0x8006
-      - SYNCBITS
+      - MARK
       - R/W
       - On Reset
       - 0
@@ -116,32 +120,94 @@ Managed register access is provided at offset 0x8000.
         * Bit 0: not included
         * Bit 1: '0' = HSYNC, '1' = VSYNC
         * Bit 2: '0' = Rising edge, '1' = Falling edge
-
+        * Bit 3: When using aggregation, use mark settings to select the first frame
 
     * - 0x8007
-      - GPIO_DIR
+      - MAGIC_MASK
+      - R/W
+      - On Reset
+      - 0
+      - None
+      - Bitmask for magic word detection and related options.
+
+        * Bits 0-15: Bitmask. If all 0, magic word detection is disabled. 
+        * Bit 31: Also check for bit-inverse mask. 
+        * Bit 30: When aggregation is enabled, wait for the first non-inverted magic word
+
+    * - 0x8008
+      - MAGIC
+      - R/W
+      - On Reset
+      - 0
+      - None
+      - After trigger, if magic_mask is not 0, wait until a specific word in the stream to start a frame. (Bits 0-15)
+
+    * - 0x8009
+      - MAGIC_WAIT
+      - R/W
+      - On Reset 
+      - 0
+      - None
+      - Max number of samples to wait from trigger to mask detection before canceling and going back to trigger detection. 0 means wait indefinitely
+
+    * - 0x800A
+      - DATAMODE
       - R/W
       - On Reset
+      - 0
+      - None
+      - Data operation mode
+
+        * Bit 0: '0' = Normal parallel mode. '1' = Serial mode 
+        * Bit 1: '1' = Include "index" field in parallel mode, '0'= Do not include it in parallel mode. 
+        * Bit 2: Number of serial streams '0' = 1 stream, '1' = 2 streams.
+        * Bit 3: reserved. 
+        * Bits 7-4: Number of bits per word - 1 (i.e.: '0x0' = 1bit, '0xF' = 16bits). 
+        * Bits 9-8 number of lines per stream '00' = 1, '01' = 2. '10' = 4, '11' = 8. 
+        * Bit 10: data order in serial mode '0' = MSB first, '1' = LSB first
+
+    * - 0x800B
+      - DATALINES0
+      - R/W 
+      - On Reset
+      - 0
+      - None
+      - Input lines for serial stream 0. Each 4 bits specify the input: 
+        0x0-0xB: Data lines 0-11. 0xC: Hsync, 0xD: Vsync, 0xE: Reserved 0xF: zero-input
+
+    * - 0x800C
+      - DATALINES0
+      - R/W 
+      - On Reset
+      - 0
+      - None
+      - Input lines for serial stream 1. Each 4 bits specify the input: 
+        0x0-0xB: Data lines 0-11. 0xC: Hsync, 0xD: Vsync, 0xE: Reserved 0xF: zero-input
+
+    * - 0x8010
+      - GPIO_DIR
+      - R/W
+      - Immediate
       - 0 
       - None
       - Bits 0-3 determine the direction of GPIO 0-3. For each bit:
 
         * 0b0: Output
         * 0b1: Input
 
-    * - 0x8008
+    * - 0x8011
       - GPIO_VAL
       - R/W
-      - On Reset
+      - Immediate
       - 0
       - None
       - Bits 0-3 determine the value of GPIO 0-3. For each bit:
 
         * 0b0: Low
         * 0b1: High
 
-    * - 0x8009
-      - GPIO_VAL
+    * - 0x8012
+      - LINK_STATUS
       - R
       - On DS90UBX LOCK or PASS pin state change
       - N/A

source/Hardware Guide/Datasheets/fmc-link-control.rst

@@ -104,6 +104,28 @@ Register Programming
       - Save link voltage to non-volatile EEPROM if greater than 0. This
         voltage will be applied after POR.
 
+    * - 0x05
+      - LINKSTATE
+      - R
+      - When LOCK or PASS change
+      - 0
+      - None 
+      - Link state
+
+        * Bit 0: LOCK
+        * Bit 1: PASS
+
+    * - 0x06
+      - LINKOPTS
+      - R/W
+      - Inmmediate
+      - 0
+      - None
+      - Misc. options for the link device
+
+        * Bit 0: `0` Port auto-shutdown disabled `1` Port auto-shutdown enabled   
+
+
 .. _onidatasheet_fmc_link_control_d2h:
 
 Device To Host Data Frames

source/Hardware Guide/Datasheets/heartbeat.rst

@@ -45,7 +45,7 @@ Register Programming
     * - 0x01
       - CLK_DIV
       - R/W
-      - On Reset
+      - Immediate
       - CLK_HZ / HB_HZ where HB_HZ is a implementation dependent default rate
       - None
       - Heartbeat clock divider ratio. Minimum value is CLK_HZ / 10e6

source/Hardware Guide/Datasheets/memory-usage.rst

@@ -45,7 +45,7 @@ Register Programming
     * - 0x01
       - CLK_DIV
       - R/W
-      - On Reset
+      - Immediate
       - CLK_HZ / HB_HZ where HB_HZ is a implementation dependent default rate
       - None
       - Read frequency clock divider ratio. Minimum value is CLK_HZ / 10e6