Huawei Solar Integration

This integration exposes the information and functions made available by Huawei Solar inverters directly via one of its Modbus interfaces in Home Assistant.

Screenshots

Inverter	Battery

Power Meter	Optimizer

HA Energy Dashboard

Prerequisites

This integration supports two connection modes to SUN2000 inverters:

• direct serial connection to the RS485A1 and RS485B1 pins of the COM port
• network connection

Detailed information can be found on the 'Connecting to the inverter' Wiki-page

Installation

1. Install this integration with HACS, or copy the contents of this repository into the custom_components/huawei_solar directory

2. Restart HA

3. Start the configuration flow:

   • 
   • Or: Go to Configuration -> Integrations and click the + Add Integration. Select Huawei Solar from the list

4. Choose whether you want to connect via serial or network connection

Serial configuration

5. Select the "USB to RS485 converter" that you connected to the RS485A1 and RS485B1 pins of your inverter. The Slave ID should be identical to the Com address set in the RS485_1 settings.

Network configuration

5. Enter the IP address and port on which the Modbus-TCP interface is available. Some pointers:

   • The port is either 502 or 6607.
   • When connecting to the inverter AP the host IP is typically 192.168.200.1 and the slave id is typically 0.
   • When connecting to an SDongle, the slave id is typically 1. Make sure to give this device a fixed IP!

   Checking the Advanced: elevate permissions checkbox will:

   • give you access to optimizer data
   • enable you to dynamically change your inverter and battery settings

6. When using the elevate permissions feature, you will be asked to enter the credentials to the installer account in a next step. These are the credentials used to connect to the inverter in the "Device Commissioning" section of the FusionSolar App. The default password is 00000a.

Inverter polling frequency

The integration will poll the inverter for new values every 30 seconds. If you wish to receive fresh inverter data less (or more) frequently, you can disable the automatic refresh in the integration's system options (Enable polling for updates) and create your own automation with your desired polling frequency.

- alias: "Huawei Solar inverter data polling"
  trigger:
    - platform: time_pattern
      hours: "*"
      minutes: "*"
      seconds: "/10"
  action:
    - service: homeassistant.update_entity
      target:
        entity_id: sensor.daily_yield

Note that optimizer data is refreshed only every 5 minutes, which matches how frequently the inverter refreshes this data.

FAQ - Troubleshooting

Q: Why do I get the error "Connection succeeded, but failed to read from inverter." while setting up this integration?

A: While the integration was able to setup the initial connection to the Huawei Inverter, it did not respond to any queries in time. This is either caused by using an invalid slave ID (typically 0 or 1, try both or ask your installer if unsure), or because an other device established a connection with the inverter, causing the integration to lose it's connection

---

Q: Will the FusionSolar App still work when using this integration?

A: The inverter will still send it's data to the Huawei cloud, and you will still be able to see live statistics from your installation in the FusionSolar App. However, if you are using this integration via the network, and you (or your installer) need to use the 'Device commissioning' feature of the app, you will need to disable this integration.

---

Q: The "Daily Yield" value reported does not match with the value from FusionSolar?

A: The "Daily Yield" reported by the inverter is the output yield of the inverter, and not the input from your solar panels. It therefore includes the yield from discharging the battery, but misses the yield used to charge the battery. FusionSolar computes the "Yield" by combining the values from "Daily Yield", "Battery Day Charge" and "Battery Day Discharge". More information on the Wiki ...

---

Q: I can't get this integration to work. What am I doing wrong?

A: First make sure that 'Modbus TCP' access is enabled in the settings of your inverter. Next, check if the port is correct. Some inverters use port 6607 instead of 502 (this can change for you after a firmware update!). If that doesn't work for you, and you intend to write an issue, make sure you have the relevant logs included. For this integration, you can enable all relevant logs by including the following lines in your configuration.yaml:

logger:
  logs:
    pymodbus: debug # only include this if you're having connectivity issues
    huawei_solar: debug
    homeassistant.components.huawei_solar: debug

By providing logs directly when creating the issue, you will likely get help much faster.