Skip to content

Firmware to turn the CC3D board into an analog USB joystick

Notifications You must be signed in to change notification settings

madmaxoft/CC3D-Analog-Joystick

Repository files navigation

CC3D-Analog-Joystick

Turns the CC3D board into a USB joystick, uses 4 analog channels and 2 digital, directly connected to the board.

This is an alternative firmware for a CC3D board, that allows the board to function as a PC Joystick. Simply plug the CC3D into a computer's USB port and plug 4 analog potentiometers (such as from an old transmitter) and 2 buttons to the board, and you'll have a functioning joystick.

Connections

The firmware expects the CC3D board to be wired in a specific way in order to be able to function. The 4 potentiometers to be used as input need to be connected to the receiver port of the board, channels 3 to 6. The two buttons are to be connected to the receiver port's channel 1 and 2. The potentiometers need to be wired as voltage dividers with the range of 0 V to 3.3 V. The CC3D's output port can be used to provide the voltage for the divider, according to the following schematic: Connection schematic

Flashing the firmware

In order to use this firmware, you will need to flash it into the CC3D board's STM32F103 chip. For this, you will need:

NOTE: SouthQuay3D has a tutorial with pictures detailing a very similar procedure: http://www.southquay3d.com/index.php?route=news/article&news_id=9 . Some of the information there is missing and some is not necessary, though.

Orient the CC3D board so that the F103 chip is facing you, the receiver port is to the left, the output port is to the right, and main poirt and flexi port are downwards. Now the main port's pins are, left-to-right: GND, Power, TX, RX ( http://opwiki.readthedocs.io/en/latest/user_manual/cc3d/cc3d.html#cables-colors-pin-outs ). Connect the GND, TX and RX pins to your FTDI dongle (TX to dongle's RX, RX to dongle's TX), but do not connect Power just yet. Locate the CC3D boot pads - two pads in the top right corner of the board, usually labeled SBL and +3.3V. Using a knife or similar, bridge the two pads and connect the Power pin to your FTDI's +5V pin. If the board blinks its Status LED, you didn't bridge the boot pads properly, unplug the Power and try again. The result should be a board with only the Power LED lit, you can un-bridge the pads at this point. Bridging this way is rather difficult to get right, it might be easier to simply solder the two pads together; they can stay soldered while you flash the firmware; then un-solder once the firmware has been flashed.

Next, fire up the STM firmware flasher tool. In the first page, choose the COM port of your FTDI dongle, leave the other settings as they are (baudrate 115200, parity Even, echo Disabled) and click Next. Immediately the second page of the tool should come up, if not, you didn't bridge the boot pads properly, close the flasher tool, unplug Power and retry. On the flasher's second page, check that it says "target is writable" and "flash size 128 KB", then click Next. On the third page, choose "STM32F1_Med-density_128K" from the dropdown and click Next.

Finally the interesting fourth page. Select the "Download to device" radio button, then click the triple dots next to the file name field. Browse to the CC3D-Analog-Joystick firmware file (.hex or .bin, doesn't matter; don't forget to change the file filter from s19 to hex or bin or you won't see the firmware file). Leave the other options on the fourth page unchanged and click Next.

The flasher tool will flash the firmware, a progressbar will be shown and when finished, you can close the tool. You have now flashed the firmware successfully, congratulations. If you soldered the boot pads together, you'll need to remove the bridge now. Remove all the cables from the CC3D board.

Compiling

To compile this project, you will need:

The makefile for this project should compile out of the box. If your GNU ARM compiler is not in path, you can use the BINPATH variable to point to the correct location: make BINPATH=/home/user/tools/gcc-arm-none-eabi-6-2017-q2-update/bin The build process will place the firmware files into the build folder

You can use the CubeMX IDE to modify the project settings, add new pin assignments etc., just open the CC3D-Analog-Joystick.ioc file. Note, however, that if you use the IDE to re-generate the project (i.e. regenerate the Makefile or create a project setup for other IDEs), you will need to revert its changes to the Middleware folder - there is one change to the USB HID class driver there that needs to be kept as-is, otherwise the board will appear as a mouse, rather than a joystick (The USH HID descriptor lives in those library files, unfortunately).

Acknowledgements

This project is inspired by @alexeystn's stm32-ppm-usb-adapter ( https://github.com/alexeystn/stm32-ppm-usb-adapter ), which was used as the base for all the user code in the firmware. It has been altered for the CC3D hardware and the code was cleaned up for better understandability. Thanks, Alexey!

Big thanks to southquay3d.com for their "CC3D flashing tutorial", I wouldn't have found out how to flash firmware to the CC3D board without their Betaflight flashing tutorial: http://www.southquay3d.com/index.php?route=news/article&news_id=9

About

Firmware to turn the CC3D board into an analog USB joystick

Resources

Stars

Watchers

Forks

Releases

No releases published

Packages

No packages published

Languages