Skip to content

USB to UART&JTAG bridge, implemented on ESP32-S2 or ESP32-S3

License

Notifications You must be signed in to change notification settings

espressif/esp-usb-bridge

Repository files navigation

ESP USB Bridge

The ESP USB Bridge is an ESP-IDF project utilizing an ESP32-S2 or an ESP32-S3 chip to create a bridge between a computer (PC) and a target microcontroller (MCU). It can serve as a replacement for USB-to-UART chips (e.g. CP210x) or a debugger.

The concept of ESP USB Bridge is shown in the following figure.

ESP USB Bridge concept

ESP USB Bridge creates a composite USB device accessible from the PC when they are connected through a USB cable. The main features are the following.

  • Serial bridge: The developer can run esptool or connect a terminal program to the serial port provided by the USB CDC. The communication is transferred in both directions between the PC and the target MCU through the ESP USB bridge.
  • JTAG/SWD bridge: openocd-esp32 can be run on the PC which will connect to the ESP USB Bridge. The bridge MCU acts again as bridge between the PC and the MCU, and transfers JTAG/SWD communication between them in both directions.
  • Mass storage device: USB Mass storage device is created which can be accessed by a file explorer in the PC. Binaries in UF2 format can be copied to this disk and the bridge MCU will use them to flash the target MCU. Currently ESP USB Bridge is capable of flashing various Espressif microcontrollers.

How to Compile the Project

ESP-IDF v5.0 or newer can be used to compile the project. Please read the documentation of ESP-IDF for setting up the environment.

  • idf.py set-target is used to select the chip the firmware is going to be built for. ESP32S2 and ESP32S3 are supported at the moment.
  • idf.py menuconfig can be used to change the default configuration. The project-specific settings are in the "Bridge Configuration" sub-menu.
  • idf.py build will build the project binaries.
  • idf.py -p PORT flash monitor will flash the Bridge MCU and open the terminal program for monitoring. Please note that PORT is the serial port created by an USB-to-UART chip connected to the serial interface of the bridge MCU (not the direct USB interface provided by bridge MCU). This serial connection has to be established only for flashing. The ESP USB Bridge can work through the USB interface after that.

The initial flashing can be done by other means as well as it is pointed out in this guide.

Development Board

A simple development board connecting an ESP32-S2 to an ESP32 serving as target MCU is shown in the schematics. The default configurations of the project were tested with this setup.

Similar boards can be manufactured and flashed with the ESP USB Bridge. The pin numbers, vendor and product identifiers and other settings can be changed in idf.py menuconfig.

Please note that every board should have its own vendor and product identifiers. There is also a possibility to register a product identifier under the Espressif vendor identifier.

Serial Bridge

The USB stack of ESP USB Bridge creates a virtual serial port through which the serial port of the target MCU is accessible. For example, this port can be /dev/ttyACMx or COMx depending on the operating system and is different from the PORT used for flashing the ESP USB Bridge.

For example, an ESP32 target MCU can be flashed and monitored with the following commands.

cd AN_ESP32_PROJECT
idf.py build
idf.py -p /dev/ttyACMx flash monitor

Please note that esptool or any terminal program can connect to the virtual serial port as well.

JTAG Bridge

The ESP USB Bridge provides a JTAG device. The following command can be used to connect to an ESP32 target MCU.

idf.py openocd --openocd-commands "-f board/esp32-bridge.cfg"

Openocd-esp32 version v0.11.0-esp32-20211220 or newer can be used as well to achieve the same:

openocd -f board/esp32-bridge.cfg

Please note that the ESP usb bridge protocol has to be selected to communicate with the target MCU. idf.py openocd without additional arguments would establish connection with the bridge MCU (if the JTAG pins are connected through a USB-to-JTAG bridge to the PC).

You might want to make your own copy of esp_usb_bridge.cfg with the appropriate product and vendor identifiers of your custom hardware:

adapter driver esp_usb_jtag
espusbjtag vid_pid 0x303a 0x1002
espusbjtag caps_descriptor 0x030A  # string descriptor index:10

The JTAG interface might need some additional setup to work. Please consult the documentation of ESP-IDF for achieving this.

SWD Bridge

The ESP USB Bridge also provides an ARM Serial Wire Debug (SWD) device using the CMSIS-DAP protocol.

On the OpenOCD side, CMSIS-DAP-related updates are continuously synced from the mainline to the Espressif fork. Therefore, it is always recommended to use the latest release or the latest master branch.

The following command can be used to access the SWD port on a target MCU

openocd -s tcl -f interface/cmsis-dap.cfg -f target/<target.cfg>.cfg -c 'adapter speed 5000'

Make sure to replace target.cfg with the actual target config file.

Currently, the ESP USB bridge supports only USB-bulk transfers as a backend. The HID backend is not supported.

Mass Storage Device

A mass storage device will show up in the PC connected to the ESP USB bridge. This can be accessed as any other USB storage disk. Binaries built in the UF2 format can be copied to this disk and the bridge MCU will flash the target MCU accordingly.

Binary uf2.bin will be generated and placed into the AN_ESP32_PROJECT/build directory by running the following commands.

cd AN_ESP32_PROJECT
idf.py uf2

License

The code in this project Copyright 2020-2022 Espressif Systems (Shanghai) Co Ltd., and is licensed under the Apache License Version 2.0. The copy of the license can be found in the LICENSE file.

Contributing

We welcome contributions to this project in the form of bug reports, feature requests and pull requests.

Issue reports and feature requests can be submitted using Github Issues: https://github.com/espressif/esp-usb-bridge/issues. Please check if the issue has already been reported before opening a new one.

Contributions in the form of pull requests should follow ESP-IDF project's contribution guidelines.

Additionally please install pre-commit hooks before committing code:

pip install pre-commit
pre-commit install

About

USB to UART&JTAG bridge, implemented on ESP32-S2 or ESP32-S3

Resources

License

Stars

Watchers

Forks

Releases

No releases published