[Deepin-Kernel-SIG] [Upstream] [linux 6.6-y] drivers: bluetooth: Sync some patches from mainline #525

opsiff · 2024-12-19T15:56:10Z

About some hardware ids, and its depend patches.
Commit:

Bluetooth: btusb: Add 3 HWIDs for MT7925
Bluetooth: btusb: Add new VID/PID 0489/e124 for MT7925
Bluetooth: btusb: Add new VID/PID 0489/e111 for MT7925
Bluetooth: btusb: Add USB HW IDs for MT7920/MT7925
Bluetooth: btusb: Add one more ID 0x13d3:0x3623 for Qualcomm WCN785x
Bluetooth: btusb: Add one more ID 0x0489:0xe0f3 for Qualcomm WCN785x
Bluetooth: btusb: add Foxconn 0xe0fc for Qualcomm WCN785x
Bluetooth: btusb: Add 2 USB HW IDs for MT7925 (0xe118/e)
Bluetooth: btusb: Add Mediatek MT7925 support ID 0x13d3:0x3608
Bluetooth: btrtl: Add the support for RTL8922A
Bluetooth: btusb: Invert LE State flag to set invalid rather then valid
Bluetooth: HCI: Invert LE State quirk to be opt-out rather then opt-in
Bluetooth: btrtl: Add the support for RTL8852BT/RTL8852BE-VT

deepin-ci-robot · 2024-12-19T15:56:42Z

[APPROVALNOTIFIER] This PR is NOT APPROVED

This pull-request has been approved by:
Once this PR has been reviewed and has the lgtm label, please ask for approval from opsiff. For more information see the Code Review Process.

The full list of commands accepted by this bot can be found here.

Needs approval from an approver in each of these files:

deepin/OWNERS

Approvers can indicate their approval by writing /approve in a comment
Approvers can cancel approval by writing /approve cancel in a comment

Add the support for RTL8852BT/RTL8852BE-VT BT controller on USB interface. The necessary firmware will be submitted to linux-firmware project. The device info from /sys/kernel/debug/usb/devices as below. T: Bus=02 Lev=02 Prnt=02 Port=05 Cnt=01 Dev#= 8 Spd=12 MxCh= 0 D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0bda ProdID=8520 Rev= 0.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00e04c000001 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Max Chou <[email protected]> Signed-off-by: Luiz Augusto von Dentz <[email protected]> (cherry picked from commit 1fb9943)

This inverts the LE State quirk so by default we assume the controllers would report valid states rather than invalid which is how quirks normally behave, also this would result in HCI command failing it the LE States are really broken thus exposing the controllers that are really broken in this respect. Link: bluez/bluez#584 Fixes: 2209158 ("Bluetooth: Adding driver and quirk defs for multi-role LE") Signed-off-by: Luiz Augusto von Dentz <[email protected]> (cherry picked from commit aae6b81260fd9a7224f7eb4fc440d625852245bb)

This inverts the LE State flag so by default we assume the controllers would report valid states rather than invalid so it is inline with the respective quirk (HCI_QUIRK_BROKEN_LE_STATES). Signed-off-by: Luiz Augusto von Dentz <[email protected]> (cherry picked from commit 0fec656d08aa59ad3ea1bba148a4f7e5618fd4d3)

Add the support for RTL8922A BT controller on USB interface. The necessary firmware will be submitted to linux-firmware project. The device info from /sys/kernel/debug/usb/devices as below. T: Bus=01 Lev=02 Prnt=02 Port=02 Cnt=01 Dev#= 3 Spd=12 MxCh= 0 D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0bda ProdID=8922 Rev= 0.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00E04C885A01 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms Signed-off-by: Max Chou <[email protected]> Signed-off-by: Luiz Augusto von Dentz <[email protected]> (cherry picked from commit a30ce2992075b9bd8824a5f1025383e8d9bc05bc)

Add the support ID (0x13d3, 0x3608) to usb_device_id table for Realtek MT7925B14L found on AW-EM637 WiFi+BT modules in 2024 Asus laptops. The device info from /sys/kernel/debug/usb/devices as below. T: Bus=03 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3608 Rev= 1.00 S: Manufacturer=MediaTek Inc. S: Product=Wireless_Device S: SerialNumber=000000000 C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I: If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us I:* If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us Signed-off-by: Pavel Nikulin <[email protected]> Signed-off-by: Luiz Augusto von Dentz <[email protected]> (cherry picked from commit cb45396f96f9671f7a18df481702e19998eb0f4b)

Add 2 USB HW IDs for MT7925 (0xe118/e) to ensure proper recognition. These HW IDs are extracted from Windows driver inf file: https://dlcdnets.asus.com/pub/ASUS/nb/Image/Driver/Bluetooth/39389/Bluetooth_DCH_MediaTek_B_V1.1037.0.433Sub2_39389.exe?model=H7606WV Patch has been tested successfully on an Asus ProArt P16 model H7606WV. Controller is recognized devices pair successfully. Signed-off-by: Michael Burch <[email protected]> Signed-off-by: Luiz Augusto von Dentz <[email protected]> (cherry picked from commit 39e4bfb466741a1364e0f690ea22961b93d2e73b)

Firmwares are already in upstream. kernel boot log as following: Bluetooth: hci0: using rampatch file: qca/rampatch_usb_00190200.bin Bluetooth: hci0: QCA: patch rome 0x190200 build 0x5656, firmware rome 0x190200 build 0x43fb Bluetooth: hci0: using NVM file: qca/nvm_usb_00190200.bin Paired BT headphone, output is good. T: Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#= 4 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e0fc Rev= 0.01 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I: If#= 1 Alt= 7 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 65 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 65 Ivl=1ms Signed-off-by: Aaron Ma <[email protected]> Signed-off-by: Luiz Augusto von Dentz <[email protected]> (cherry picked from commit add1b1656f909c41aa0186fe75e7a42e2c0d2188)

Add one more part with ID (0x0489, 0xe0f3) to usb_device_id table for Qualcomm WCN785x, and its device info from /sys/kernel/debug/usb/devices is shown below: T: Bus=01 Lev=01 Prnt=01 Port=13 Cnt=03 Dev#= 4 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e0f3 Rev= 0.01 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I: If#= 1 Alt= 7 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 65 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 65 Ivl=1ms Signed-off-by: Zijun Hu <[email protected]> Signed-off-by: Luiz Augusto von Dentz <[email protected]> (cherry picked from commit 45f745dd1ac880ce299c0f92b874cda090ddade6)

Add one more part with ID (0x13d3, 0x3623) to usb_device_id table for Qualcomm WCN785x, and its device info from /sys/kernel/debug/usb/devices is shown below: T: Bus=01 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3623 Rev= 0.01 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I: If#= 1 Alt= 7 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 65 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 65 Ivl=1ms Signed-off-by: Zijun Hu <[email protected]> Signed-off-by: Luiz Augusto von Dentz <[email protected]> (cherry picked from commit e69bcffce21c649a23645b20eb527b3d1ce6fc49)

Add HW IDs for wireless module. These HW IDs are extracted from Windows driver inf file and the test for card bring up successful. MT7920 HW IDs test with below patch. https://patchwork.kernel.org/project/bluetooth/ patch/[email protected]/ Patch has been tested successfully and controller is recognized devices pair successfully. MT7920 module bring up message as below. Bluetooth: Core ver 2.22 Bluetooth: HCI device and connection manager initialized Bluetooth: HCI socket layer initialized Bluetooth: L2CAP socket layer initialized Bluetooth: SCO socket layer initialized Bluetooth: hci0: HW/SW Version: 0x008a008a, Build Time: 20240930111457 Bluetooth: hci0: Device setup in 143004 usecs Bluetooth: hci0: HCI Enhanced Setup Synchronous Connection command is advertised, but not supported. Bluetooth: hci0: AOSP extensions version v1.00 Bluetooth: hci0: AOSP quality report is supported Bluetooth: BNEP (Ethernet Emulation) ver 1.3 Bluetooth: BNEP filters: protocol multicast Bluetooth: BNEP socket layer initialized Bluetooth: MGMT ver 1.22 Bluetooth: RFCOMM TTY layer initialized Bluetooth: RFCOMM socket layer initialized Bluetooth: RFCOMM ver 1.11 MT7925 module bring up message as below. Bluetooth: Core ver 2.22 Bluetooth: HCI device and connection manager initialized Bluetooth: HCI socket layer initialized Bluetooth: L2CAP socket layer initialized Bluetooth: SCO socket layer initialized Bluetooth: hci0: HW/SW Version: 0x00000000, Build Time: 20240816133202 Bluetooth: hci0: Device setup in 286558 usecs Bluetooth: hci0: HCI Enhanced Setup Synchronous Connection command is advertised, but not supported. Bluetooth: hci0: AOSP extensions version v1.00 Bluetooth: BNEP (Ethernet Emulation) ver 1.3 Bluetooth: BNEP filters: protocol multicast Bluetooth: BNEP socket layer initialized Bluetooth: MGMT ver 1.22 Bluetooth: RFCOMM TTY layer initialized Bluetooth: RFCOMM socket layer initialized Bluetooth: RFCOMM ver 1.11 Signed-off-by: Jiande Lu <[email protected]> Signed-off-by: Luiz Augusto von Dentz <[email protected]> (cherry picked from commit a94bc93a305bdcb20cc62978c334cace932b1be0)

Add VID 0489 & PID e111 for MediaTek MT7925 USB Bluetooth chip. The information in /sys/kernel/debug/usb/devices about the Bluetooth device is listed as the below. T: Bus=02 Lev=02 Prnt=02 Port=04 Cnt=02 Dev#= 4 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e111 Rev= 1.00 S: Manufacturer=MediaTek Inc. S: Product=Wireless_Device S: SerialNumber=000000000 C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us I: If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us Signed-off-by: Hao Qin <[email protected]> Signed-off-by: Luiz Augusto von Dentz <[email protected]> (cherry picked from commit faa5fd605d2081b6c9fa2355b59582d4ccd24b16)

Add VID 0489 & PID e124 for MediaTek MT7925 USB Bluetooth chip. The information in /sys/kernel/debug/usb/devices about the Bluetooth device is listed as the below. T: Bus=01 Lev=01 Prnt=01 Port=08 Cnt=02 Dev#= 3 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e124 Rev= 1.00 S: Manufacturer=MediaTek Inc. S: Product=Wireless_Device S: SerialNumber=000000000 C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us I: If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us Signed-off-by: Jonathan McCrohan <[email protected]> Signed-off-by: Luiz Augusto von Dentz <[email protected]> (cherry picked from commit 679cb60fd60774798719c3e449874a168642a8e6)

Add below HWIDs for MediaTek MT7925 USB Bluetooth chip. VID 0x0489, PID 0xe14f VID 0x0489, PID 0xe150 VID 0x0489, PID 0xe151 Patch has been tested successfully and controller is recognized device pair successfully. MT7925 module bring up message as below. Bluetooth: Core ver 2.22 Bluetooth: HCI device and connection manager initialized Bluetooth: HCI socket layer initialized Bluetooth: L2CAP socket layer initialized Bluetooth: SCO socket layer initialized Bluetooth: hci0: HW/SW Version: 0x00000000, Build Time: 20240816133202 Bluetooth: hci0: Device setup in 286558 usecs Bluetooth: hci0: HCI Enhanced Setup Synchronous Connection command is advertised, but not supported. Bluetooth: hci0: AOSP extensions version v1.00 Bluetooth: BNEP (Ethernet Emulation) ver 1.3 Bluetooth: BNEP filters: protocol multicast Bluetooth: BNEP socket layer initialized Bluetooth: MGMT ver 1.22 Bluetooth: RFCOMM TTY layer initialized Bluetooth: RFCOMM socket layer initialized Bluetooth: RFCOMM ver 1.11 Signed-off-by: Jiande Lu <[email protected]> Signed-off-by: Luiz Augusto von Dentz <[email protected]> (cherry picked from commit de7dcf9d1df4b0009735756d0a2adff09c3f21d4)

deepin-ci-robot · 2024-12-20T02:48:59Z

deepin pr auto review

代码审查意见：

在btintel_setup_combined函数中，移除了对ver.hw_variant == 0x08 && ver.fw_variant == 0x22的判断，这可能会影响某些特定硬件和固件的quirk设置。建议确认这一改动是否符合预期，并确保没有遗漏相关的测试用例。
在btintel_pcie_setup_internal和btmtksdio_setup函数中，移除了对HCI_QUIRK_VALID_LE_STATES的设置，这可能会影响LE状态的有效性判断。建议确认这一改动是否符合预期，并确保没有遗漏相关的测试用例。
在btrtl.c文件中，新增了对RTL_ROM_LMP_8922A和RTL_ROM_LMP_8852A的quirk设置，但未在代码中看到对应的逻辑处理。建议确认这些新增的quirk设置是否有对应的逻辑处理，以及是否需要更新相关的文档和注释。
在btusb.c文件中，将BTUSB_VALID_LE_STATES改为BTUSB_INVALID_LE_STATES，这可能会影响LE状态的有效性判断。建议确认这一改动是否符合预期，并确保没有遗漏相关的测试用例。
在hci_qca.c文件中，将QCA_CAP_VALID_LE_STATES改为!QCA_CAP_VALID_LE_STATES，这可能会影响LE状态的有效性判断。建议确认这一改动是否符合预期，并确保没有遗漏相关的测试用例。
在hci_core.h文件中，将HCI_QUIRK_VALID_LE_STATES改为HCI_QUIRK_BROKEN_LE_STATES，这可能会影响LE状态的有效性判断。建议确认这一改动是否符合预期，并确保没有遗漏相关的测试用例。
在hci_event.c文件中，对LE状态的有效性判断进行了修改，这可能会影响LE连接的建立。建议确认这一改动是否符合预期，并确保没有遗漏相关的测试用例。

总体来说，这些改动涉及到对LE状态的有效性判断的修改，需要确保这些改动不会影响蓝牙设备的正常工作，并且已经通过了充分的测试。

deepin-ci-robot requested review from BLumia and hello666888999 December 19, 2024 15:56

opsiff force-pushed the linux-6.6.y branch from 2ffdc33 to 8ead783 Compare December 20, 2024 02:37

rtkbt-max and others added 13 commits December 20, 2024 10:48

opsiff force-pushed the btusb-hw-support branch from 00c1909 to 17906dd Compare December 20, 2024 02:48

opsiff merged commit 6aa25f3 into linux-6.6.y Dec 23, 2024
7 of 10 checks passed

Provide feedback

Saved searches

Use saved searches to filter your results more quickly

[Deepin-Kernel-SIG] [Upstream] [linux 6.6-y] drivers: bluetooth: Sync some patches from mainline #525

[Deepin-Kernel-SIG] [Upstream] [linux 6.6-y] drivers: bluetooth: Sync some patches from mainline #525

opsiff commented Dec 19, 2024 •

edited

Loading

deepin-ci-robot commented Dec 19, 2024

deepin-ci-robot commented Dec 20, 2024

[Deepin-Kernel-SIG] [Upstream] [linux 6.6-y] drivers: bluetooth: Sync some patches from mainline #525

[Deepin-Kernel-SIG] [Upstream] [linux 6.6-y] drivers: bluetooth: Sync some patches from mainline #525

Conversation

opsiff commented Dec 19, 2024 • edited Loading

deepin-ci-robot commented Dec 19, 2024

deepin-ci-robot commented Dec 20, 2024

deepin pr auto review

opsiff commented Dec 19, 2024 •

edited

Loading