Readd DARWINF435 target (#297)

* Readd DARWINF435 target

This should be caused by incorrect LF file, I have revised it again. 
Accidentally shut down the previous PR, so I can only submit again

* Update config.h

---------

Co-authored-by: Mark Haslinghuis <[email protected]>

configs/DARWINF435/config.h

@@ -0,0 +1,103 @@
+/*
+ * This file is part of Betaflight.
+ *
+ * Betaflight is free software. You can redistribute this software
+ * and/or modify this software under the terms of the GNU General
+ * Public License as published by the Free Software Foundation,
+ * either version 3 of the License, or (at your option) any later
+ * version.
+ *
+ * Betaflight is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
+ *
+ * See the GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this software.
+ *
+ * If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#pragma once
+
+#define FC_TARGET_MCU        AT32F435G
+
+#define BOARD_NAME           DARWINF435
+#define MANUFACTURER_ID      DAFP
+
+#define USE_ACC
+#define USE_GYRO
+
+#define USE_ACC_SPI_MPU6000
+#define USE_GYRO_SPI_MPU6000
+
+#define USE_ACC_SPI_ICM42688P
+#define USE_GYRO_SPI_ICM42688P
+
+#define USE_BARO
+#define USE_BARO_DPS310
+
+#define USE_FLASH
+#define USE_FLASH_W25Q128FV
+
+#define USE_MAX7456
+
+#define BEEPER_PIN              PC15
+#define MOTOR1_PIN              PB6
+#define MOTOR2_PIN              PB7
+#define MOTOR3_PIN              PA3
+#define MOTOR4_PIN              PB1
+#define LED_STRIP_PIN           PA8
+#define UART1_TX_PIN            PA9
+#define UART2_TX_PIN            PA2
+#define UART3_TX_PIN            PB11
+#define UART5_TX_PIN            PB9
+#define UART7_TX_PIN            PB4
+#define UART1_RX_PIN            PA10
+#define UART2_RX_PIN            PB0
+#define UART3_RX_PIN            PB10
+#define UART5_RX_PIN            PB8
+#define UART7_RX_PIN            PB3
+#define I2C2_SCL_PIN            PH2
+#define I2C2_SDA_PIN            PH3
+#define LED0_PIN                PC13
+#define LED1_PIN                PC14
+#define SPI1_SCK_PIN            PA5
+#define SPI2_SCK_PIN            PB13
+#define SPI1_SDI_PIN            PA6
+#define SPI2_SDI_PIN            PB14
+#define SPI1_SDO_PIN            PA7
+#define SPI2_SDO_PIN            PB15
+#define ADC_VBAT_PIN            PA0
+#define ADC_CURR_PIN            PA1
+#define FLASH_CS_PIN            PB5
+#define MAX7456_SPI_CS_PIN      PB12
+#define GYRO_1_EXTI_PIN         PA15
+#define GYRO_1_CS_PIN           PA4
+
+#define TIMER_PIN_MAPPING       TIMER_PIN_MAP(0, PA8, 1, 7) \
+                                TIMER_PIN_MAP(1, PB6, 1, 0) \
+                                TIMER_PIN_MAP(2, PB7, 1, 1) \
+                                TIMER_PIN_MAP(3, PA3, 1, 2) \
+                                TIMER_PIN_MAP(4, PB1, 2, 3)
+
+#define ADC_INSTANCE            ADC1
+#define ADC1_DMA_OPT            11
+
+#define DEFAULT_BLACKBOX_DEVICE BLACKBOX_DEVICE_FLASH
+#define DEFAULT_DSHOT_BURST DSHOT_DMAR_AUTO
+#define DEFAULT_DSHOT_TELEMETRY DSHOT_TELEMETRY_ON
+#define DEFAULT_CURRENT_METER_SOURCE CURRENT_METER_ADC
+#define DEFAULT_VOLTAGE_METER_SOURCE VOLTAGE_METER_ADC
+#define BEEPER_INVERTED
+#define SYSTEM_HSE_MHZ          8
+#define GYRO_1_SPI_INSTANCE     SPI1
+#define GYRO_1_ALIGN CW180_DEG
+#define MAX7456_SPI_INSTANCE    SPI2
+#define FLASH_SPI_INSTANCE      SPI2
+#define BARO_I2C_INSTANCE       (I2CDEV_2)
+#define USE_I2C_PULLUP
+#define LED0_INVERTED
+#define LED1_INVERTED
+#define DEFAULT_CURRENT_METER_SCALE 125