We are happy to present you our integration of the Unitree Go2 with ROS2 over Wi-Fi, that was designed by the talented @tfoldi. You can explore his groundbreaking work at go2-webrtc.
This repo will empower your Unitree GO2 AIR/PRO/EDU robots with ROS2 capabilities, using both WebRTC (Wi-Fi) and CycloneDDS (Ethernet) protocols.
If you are using WebRTC (Wi-Fi) protocol, close the connection with a mobile app before connecting to the robot.
- URDF ✅
- Joint states sync in real time ✅
- IMU sync in real time ✅
- Joystick control in real time ✅
- Go2 topics info in real time ✅
- Foot force sensors info in real time ✅
- Lidar stream (added pointCloud2) ✅
- Camera stream ✅
- Foxglove bridge ✅
- Laser Scan ✅
- Multi robot support ✅
- WebRTC and CycloneDDS support ✅
- Creating a PointCloud map and store it ✅
- SLAM (slam_toolbox) ✅
- Navigation (nav2) ✅
- Object detection
- AutoPilot
If you're as enthusiastic about this project as we are, please consider giving it a ⭐ star!!!
Your encouragement fuels our passion and helps us develop our RoadMap further. We welcome any help or suggestions you can offer!
Together, let's push the boundaries of what's possible with the Unitree Go2 and ROS2!
✨ Full ROS2 SDK support for your Unitree GO2
🤖 Compatible with AIR, PRO, and EDU variants
👣 Access to foot force sensors feedback (available on some GO2 PRO models or EDU)
Tested systems and ROS2 distro
| systems | ROS2 distro | Build status |
|---|---|---|
| Ubuntu 22.04 | iron | |
| Ubuntu 22.04 | humble | |
| Ubuntu 22.04 | rolling | |
mkdir -p ros2_ws
cd ros2_ws
git clone --recurse-submodules https://github.com/abizovnuralem/go2_ros2_sdk.git src
sudo apt install ros-$ROS_DISTRO-image-tools
sudo apt install ros-$ROS_DISTRO-vision-msgs
sudo apt install python3-pip clang portaudio19-dev
cd src
pip install -r requirements.txt
cd ..Pay attention to any error messages. If pip install does not complete cleanly, various features will not work. For example, open3d does not yet support python3.12 and therefore you will need to set up a 3.11 venv first etc.
Install rust language support following these instructions. Then, install version 1.79 of cargo, the rust package manager.
rustup install 1.79.0
rustup default 1.79.0cargo should now be available in the terminal:
cargo --versionBuild go2_ros_sdk. You need to have ros2 and rosdep installed. If you do not, follow these instructions. Then:
source /opt/ros/$ROS_DISTRO/setup.bash
rosdep install --from-paths src --ignore-src -r -y
colcon buildDon't forget to set up your Go2 robot in Wifi-mode and obtain the IP. You can use the mobile app to get it. Go to Device -> Data -> Automatic Machine Inspection and look for STA Network: wlan0.
source install/setup.bash
export ROBOT_IP="robot_ip" #for muliple robots, just split by ,
export CONN_TYPE="webrtc"
ros2 launch go2_robot_sdk robot.launch.pyThe robot.launch.py code starts many services/nodes simultaneously, including
- robot_state_publisher
- ros2_go2_video (front color camera)
- pointcloud_to_laserscan_node
- go2_robot_sdk/go2_driver_node
- go2_robot_sdk/lidar_to_pointcloud
- rviz2
joy(ROS2 Driver for Generic Joysticks and Game Controllers)teleop_twist_joy(facility for tele-operating Twist-based ROS2 robots with a standard joystick. Converts joy messages to velocity commands)twist_mux(twist_multiplexer with source prioritization)- foxglove_launch (launches the foxglove bridge)
- slam_toolbox/online_async_launch.py
- av2_bringup/navigation_launch.py
When you run robot.launch.py, rviz will fire up, lidar data will begin to accumulate, the front color camera data will be displayed too (typically after 4 seconds), and your dog will be waiting for commands from your joystick (e.g. a X-box controller). You can then steer the dog through your house, e.g., and collect LIDAR mapping data.
The goal of SLAM overall, and the slam_toolbox in particular, is to create a map. The slam_toolbox is a grid mapper - it thinks about the world in terms of a fixed grid that the dog operates in. When the dog initially moves through a new space, data accumulate and the developing map is and published it to the /map topic. The goal of Nav2 is to navigate and perform other tasks in this map.
The rviz settings that are used upon initial launch (triggered by ros2 launch go2_robot_sdk robot.launch.py) showcase various datastreams.
RobotModelis the dimensionally correct model of the G02PointCloud2are the raw LIDAR data transformed into 3D objects/constraintsLaserScanare lower level scan data before translation into an x,y,z frameImageare the data from the front-facing color cameraMapis the map being created by theslam_toolboxOdometryis the history of directions/movements of the dog
If there is too much going on in the initial screen, deselect the map topic to allow you to see more.
Use painter's tape to mark a 'dock' rectangle (or use a real dock) to create a defined starting point for your dog on your floor. In the rviz SlamToolboxPlugin, on the left side of the your rviz screen, select "Start At Dock". Then, use your controller to manually explore a space, such as a series of rooms. You will see the map data accumulating in rviz. In this map, white, black and grey pixels represent the free, occupied, and unknown space, respectively. When you are done mapping, enter a file name into the "Save Map" field and click "Save Map". Then enter a file name into "Serialize Map" field and click "Serialize Map". Now, you should have 2 new files in /ros2_ws:
map_1.yaml: the metadata for the map as well as the path to the .pgm image file.
map_1.pgm: the image file with white, black and grey pixels representing the free, occupied, and unknown space.
map_1.data:
map_1.posegraph: The next time you start the system, the map can be loaded and is ready for you to complete/extend by mapping more spaces. Upon restart and loading a map, the dog does not know where it is relative to the map you created earlier. Assuming you rebooted the dog in its marked rectangle, or in an actual dock, it will have a high quality initial position and angle.
As shown in the rviz Navigation 2 plugin, the system will come up in:
Navigation: active
Localization: inactive
Feedback: unknownThen, load your map via the SlamToolboxPlugin (enter your map's filename (without any extension) in the 'Deserialize Map' field and then click 'Deserialize Map').
WARNING: please make sure that (1) the dog is correctly oriented WRT to the map and (2) the map itself is sane and corresponds to your house. Especially if you have long corridors, the overall map can be distorted relative to reality, and this means that the route planner will try to route your dog through walls, leaving long scratches in your walls.
You can now give the dog its first target, via 'Nav2 Goal' in the rviz menu. Use the mouse cursor to provide a target to navigate to.
NOTE: the Nav2 Goal cursor sets both the target position and the final angle of the dog, that you wish the dog to adopt upon reaching the target (need to double check). The long green arrow that is revealed when you click an point and keep moving your mouse cursor is the angle setter.
Until you have some experience, we suggest following your dog and picking it up when it is about to do something silly.
NOTE: Virtually all fault behaviors - spinning in circles, running into walls, trying to walk through walls, etc reflect (1) a map that is incorrect, (2) incorrect initial position/angle of the dog relative to that map, or (3) inability to compute solutions/paths based on overloaded control loops. To prevent #3, which results in no motion or continuous spinning, the key loop rates (controller_frequency: 3.0 and expected_planner_frequency: 1.0 have been set to very conservative rates).
This capability is directly based on J. Francis's work. Launch the go2_ro2_sdk. After a few seconds, the color image data will be available at go2_camera/color/image. On another terminal enter:
source install/setup.bash
ros2 run coco_detector coco_detector_nodeThere will be a short delay the first time the node is run for PyTorch TorchVision to download the neural network. You should see a download progress bar. TorchVision cached for subsequent runs.
On another terminal, to view the detection messages:
source install/setup.bash
ros2 topic echo /detected_objectsThe detection messages contain the detected object (class_id) and the score, a number from 0 to 1. For example: detections:results:hypothesis:class_id: giraffe and detections:results:hypothesis:score: 0.9989. The bbox:center:x and bbox:center:y contain the centroid of the object in pixels. These data can be used to implement real-time object following for animals and people. People are detected as detections:results:hypothesis:class_id: person.
To view the image stream annotated with the labels and bounding boxes:
source install/setup.bash
ros2 run image_tools showimage --ros-args -r /image:=/annotated_imageExample Use:
ros2 run coco_detector coco_detector_node --ros-args -p publish_annotated_image:=False -p device:=cuda -p detection_threshold:=0.7This will run the coco detector without publishing the annotated image (it is True by default) using the default CUDA device (device=cpu by default). It sets the detection_threshold to 0.7 (it is 0.9 by default). The detection_threshold should be between 0.0 and 1.0; the higher this number the more detections will be rejected. If you have too many false detections try increasing this number. Thus only Detection2DArray messages are published on topic /detected_objects.
To save raw LIDAR data, export the following:
export MAP_SAVE=True
export MAP_NAME="3d_map"Every 10 seconds, pointcloud data (in .ply format) will be saved to the root folder of the repo. NOTE: This is not a Nav2 map but a raw data dump of LIDAR data useful for low-level debugging.
If you want to connect several robots for collaboration:
export ROBOT_IP="robot_ip_1, robot_ip_2, robot_ip_N"export CONN_TYPE="webrtc"or
export CONN_TYPE="cyclonedds"
To use Foxglove, you need to install Foxglove Studio:
sudo snap install foxglove-studio
- Open Foxglove Studio and press "Open Connection".
- In the "Open Connection" settings, choose "Foxglove WebSocket" and use the default configuration ws://localhost:8765, then press "Open".
If you are running ROS2 under WSL2 - you may need to configure Joystick\Gamepad to navigate the robot.
-
Step 1 - share device with WSL2
Follow steps here https://learn.microsoft.com/en-us/windows/wsl/connect-usb to share your console device with WSL2
-
Step 2 - Enable WSL2 joystick drivers
WSL2 does not come by default with the modules for joysticks. Build WSL2 Kernel with the joystick drivers. Follow the instructions here: https://github.com/dorssel/usbipd-win/wiki/WSL-support#building-your-own-wsl-2-kernel-with-additional-drivers If you're comfortable with WSl2, skip the export steps and start at
Install prerequisites.Before buiding, edit
.configfile and update the CONFIG_ values listed in this GitHub issue: microsoft/WSL#7747 (comment) -
Step 3 - Give permissions to /dev/input devices
Once you've finished the guides under Step 3 - you should be able to see your joystick device under /dev/input
ls /dev/input by-id by-path event0 js0
By default /dev/input/event* will only have root permissions, so joy node won't have access to the joystick
Create a file
/etc/udev/rules.d/99-userdev-input.ruleswith the following content:KERNEL=="event*", SUBSYSTEM=="input", RUN+="/usr/bin/setfacl -m u:YOURUSERNAME:rw $env{DEVNAME}"Run as root:
udevadm control --reload-rules && udevadm trigger -
Step 3 - verify that joy node is able to see the device properly.
Run
ros2 run joy joy_enumerate_devicesID : GUID : GamePad : Mapped : Joystick Device Name ------------------------------------------------------------------------------- 0 : 030000005e040000120b000007050000 : true : false : Xbox Series X Controller
Special thanks to:
- @tfoldi (Tamas) for his idea and talent to create a webrtc connection method between python and unitree GO2;
- @budavariam for helping with lidar issues;
- @legion1581 for a new webrtc method, that is working with 1.1.1 firmware update;
- @alex.lin for his passion in ros1 ingration;
- @alansrobotlab for his passion in robotics and helping me to debug new webrtc method;
- @giangalv (Gianluca Galvagn) for helping me debug new issues with webrtc;
- Many many other open source contributors! and TheRoboVerse community!
This project is licensed under the BSD 2-clause License - see the LICENSE file for details.