Committing vip7002w-release-vip7002w-20241105090453_rel-205_rdk16_oe31

Committing for open source release compliance

Signed-off-by: varadharajan-v <[email protected]>

asix-standalone-driver/readme

@@ -0,0 +1,142 @@
+![ASIX](https://www.asix.com.tw/upload/2019_12_061/20191206160042ixfpyg5Wz1.jpg)
+
+# [ASIX USB Ethernet ICs](https://www.asix.com.tw/en/product/USBEthernet)
+* ASIX AX88772A USB 2.0 Fast Ethernet Network Adapter
+* ASIX AX88772B USB 2.0 Fast Ethernet Network Adapter
+* ASIX AX88772C USB 2.0 Fast Ethernet Network Adapter
+
+## Prerequisites
+
+Prepare to build the driver, you need the Linux kernel sources installed on the 
+build machine, and make sure that the version of the running kernel must match 
+the installed kernel sources. If you don't have the kernel sources, you can get 
+it from [The Linux Kernel Archives](www.kernel.org) or contact to your Linux 
+ distributor. If you don't know how to do, please refer to KERNEL-HOWTO.
+
+**Note**: Please make sure the kernel is built with one of the "Support for 
+Host-side, EHCI, OHCI, or UHCI" option support.
+
+## Conditional Compilation Flag
+
+* AX_FORCE_BUFF_ALIGN 
+
+There are alignment issues of USB buffer in some USB host controllers. 
+Turn on this flag if the implementation of your USB host controller 
+cannot handle non-double word aligned buffer. 
+When turn on this flag, driver will fixup egress packet aligned on double 
+word boundary before deliver to USB host controller. 
+Setting: 
+   1 -> Enable TX buffers forced on double word alignment. 
+   0 -> Disable TX buffers forced on double word alignment. 
+Default:
+   0
+
+## Getting Start
+1. Extract the compressed driver source file to your template directory by the 
+ following command:
+``` shell=
+	$tar -xf DRIVER_SOURCE_PACKAGE.tar.bz2
+```
+
+2. Now, the driver source files should be extracted under the current directory. 
+Executing the following command to compile the driver:
+``` shell=
+	$make
+```
+
+3. If the compilation is well, the asix.ko will be created under the current 
+ directory.
+
+4. If you want to use modprobe command to mount the driver, executing the 
+ following command to install the driver into your Linux:
+``` shell=
+	$make install
+```
+
+## Usage
+1. If you want to load the driver manually, go to the driver directory and 
+ execute the following commands:
+``` shell=
+	$sudo insmod asix.ko
+```
+
+2. If you had installed the driver during driver compilation, then you can use 
+ the following command to load the driver automatically.
+``` shell=
+	$sudo modprobe asix
+```
+
+If you want to unload the driver, just executing the following command:
+``` shell=
+	$sudo rmmod asix
+```
+
+## Special define
+There is a RX_SKB_COPY preprocessor define in asix.h can solve rx_throttle problem 
+in some version of 3.4 Linux kernel. Removing the comment before the define can 
+ enable this feature.
+
+-------------------------------------------------------------------------------
+# Programmer
+ASIX USB Ethernet Linux Command Line Programming Tool
+
+##  Getting Start
+
+1. Extract the compressed driver source file to your temporary directory by the
+following command:
+``` shell=
+	$tar -xf DRIVER_SOURCE_PACKAGE.tar.bz2
+```
+
+2. Now, the driver source files should be extracted under the current directory.
+Executing the following command to compile the driver:
+```shell=
+	$make
+```
+
+3. If the compilation is well, the ioctl will be created under the current 
+ directory.
+
+**Note**: The default way to find the interface is to scan the ASIX device using
+ the ethx (x: 0~255).It is defined in the file, **command.h**.
+```c=
+	(As follows)
+	...
+	// DEFAULT_SCAN   : scan "eth0" - "eth255"
+	// INTERFACE_SCAN : scan all available network interfaces
+	#define NET_INTERFACE	DEFAULT_SCAN
+	#define	DEFAULT_SCAN	0x00
+	#define	INTERFACE_SCAN	0x01
+	...
+```
+Adjust the contents of #define NET_INTERFACE to select the method you want.
+
+## AX88772x EEPROM Programmer
+
+1. If you want to read out values of the EEPROM to a file, go to the driver directory 
+ and execute the following command:
+``` shell=
+	$./ioctl reeprom file_name eeprom_size
+```
+
+2. If you want to write values of a file to the EEPROM, go to the driver directory 
+ and execute the following command:
+``` shell=
+	$./ioctl weeprom file_name eeprom_size
+```
+
+3. If you want to change the MAC address of a dongle, go to the driver directory 
+ and execute the following command:
+``` shell=
+	$./ioctl chgmac mac_addr eeprom_size
+```
+
+4. If you need more information about the instructions, go to the driver directory 
+ and execute the following commands:
+``` shell=
+	$./ioctl reeprom help
+```
+or
+``` shell=
+	$./ioctl weeprom help
+```

asix-standalone-driver/recipeinfo

@@ -0,0 +1,3 @@
+LICENSE: GPLv2
+PR: r0
+PV: 1.0