add SB_Combo_V2

docs/SB_Combo_V2.md

@@ -0,0 +1,229 @@
+# SB Combo V2
+
+
+
+![产品主图](assets/SB_Combo_V2_top.png)
+
+
+
+# Introduction
+
+SB CAN V2 is a newly designed SB tool board running Klipper firmware. Based on STM32F072, it provides two communication modes: CANBUS and USB. The onboard USBHUB has up to three USB interfaces, which can be used to connect to the scanning leveling sensor (Scanner Leveling Sensor,such as IDM or Cartographer )and AI camera, etc. It can also be connected vertically with an optional board for easy use.
+
+# Featrues
+
+- STM32F072 MCU, supports Klipper Firmware
+- **6-layer PCB design, all solid capacitors and tantalum capacitors**
+- Onboard 2 M3 3.5mm isolation columns, no need for printed parts, easy to install
+- Onboard CAN/USB switch
+- Onboard RESET and BOOT0 buttons for easy firmware update
+- Fan control/heating both use independent high-power MOS, safer and lower heat
+- **Onboard 5V@3A DC-DC, 5V peak load can reach 15W**
+- XT30 interface, customized connection cable comes with the board
+- **Onboard USB2.0 HUB, 3x USB2.0 interface (one of which is located on the auxiliary board)**
+- **Support CAN / USB2.0 connection**
+- Supports auxiliary board connection For front cover quick install & remove Support
+- Auxiliary board connection for quick installation and removal of the front cover. You can add 1x USB, 2x 3-wire fans, 1x RGB by the auxiliary board
+- Onboard TMC2209
+- 3x Fans, 3x IO with level converter, 1x RGB,1x Heat, 1x thermistor,1x status LED
+- ADXL345 Accelerometer onboard
+- USB-C onboard for Firmware update
+
+# Application
+
+Voron StealthBurner  Head
+
+# Hardware specification
+
+| Function                | SB Combo V2                                                | SB TH CAN V1.3     |
+| ----------------------- | ---------------------------------------------------------- | ------------------ |
+| Microcontroller         | STM32F072CBT6                                              | STM32F072CBT6      |
+| Accelerometer           | ADXL345                                                    | ADXL345            |
+| USB Port                | 2 + 1 (For STM32F072) + 1(on aux board), Powered by CH334P | -                  |
+| Fan                     | 3+2 (on aux board)                                         | 2                  |
+| Heating output          | 1                                                          | 1                  |
+| Temperature measurement | 1 (PH2.0 connector) + 1 (on board thermistor)              | 1(PH2.0 connector) |
+| Voltage monitoring      | 5V, 24V                                                    | -                  |
+| Motor drive             | TMC2209                                                    | TMC2209            |
+| Signal input and output | 3                                                          | 3                  |
+| RGB light strip control | 1 + 1 (on aux board)                                       | 1                  |
+| Aux Board support       | Yes                                                        | No                 |
+| Onboard mounting nut    | Yes                                                        | No                 |
+
+# Operating limits
+
+| **Stepper drivers**           | Up to 2.0A peak current                     |
+| ----------------------------- | ------------------------------------------- |
+| **Mosfets Outputs**           | HE0 up to 5A , Fan up to 2.5A each          |
+| **Input power voltage**       | 11V to 24V for VIN up to 10A                |
+| **Inputs/Outputs**            | Signal 20ma maximum, RGB 2.5A total maximum |
+| **5V and 3.3V current limit** | 5V@3A ，[email protected]                           |
+
+# Physical Connections
+
+## Pin Out
+
+![img](images/SB_Combo_V2/SB_Combo_V2_PIN.png)
+
+### On the SB_Combo Board
+
+IO.0 and IO.1 are located in the same connector and can be used as XY endstops, and IO.2 can be used as a probe. In addition, IO.0, IO.1, and IO.2 have level conversion (with pull-up resistors) and voltage selectors (5V or 24V), which can be compatible with a variety of sensors. The three IOs and RGB can be used as inputs or outputs, and can be configured according to your needs.
+```
+IO.0: PA2
+IO.1: PA3 
+IO.2: PA0
+RGB: PB11
+
+FAN0: PB6
+FAN1: PB5
+FAN2: PA4
+
+Heat: PC15
+Thermistor: PA6
+
+Driver_EN: PA15
+Driver_DIR: PA8
+Driver_STEP: PB3
+Driver_UART: PA10
+Driver_TX: PA9
+Driver_DIAG: PB4
+
+spi_bus: spi2
+adxl345_cs_pin: PB12
+adxl345_spi_software_sclk_pin: PB13
+adxl345_spi_software_mosi_pin: PB15
+adxl345_spi_software_miso_pin: PB14
+
+CAN_RX: PB8
+CAN_TX: PB9
+
+5V_Monitor: PA1
+24V_MOnitor: PA5
+TMC_Thermistor: PB1
+```
+### On the AUX Board
+
+```
+ext_IO.6: PA7
+ext_fan0: PB0
+ext_IO.5: PB10
+ext_fan1: PB7
+RGB: PC14
+```
+## Description of Connections：
+
+![SB_Combo_V2_connector_bottom](images/SB_Combo_V2/SB_Combo_V2_connector_bottom.png)
+
+![SB_Combo_V2_connector_top](images/SB_Combo_V2/SB_Combo_V2_connector_top.png)
+
+
+
+## LED indications：
+
+![img](images/SB_Combo_V2/SB_Combo_V2_LED.png)
+
+| LED name | Indicate                                                     | Remark |
+| -------- | ------------------------------------------------------------ | ------ |
+| 3V3      | Lights up:  Power supply OK.<br/>Turns off : Power supply failure. 3.3V is obtained by converting 24V to 5V through DC-DC and then to 3.3V through LDO, so there may be a short circuit/open circuit in 24V/5V/3.3V.<br/> |        |
+| HUB      | Lights up:  The USB has at least one connection.<br/>Turns off: The USB has no connection. |        |
+| STATUS   | When using katakulpt<br/>- Blinking: Entering download mode;<br/>- Off/Always on: Not in download mode, the status is generally determined by config;<br/>- The LED is controlled by PC13 and lights up at a high level. For customized usage, please refer to julianschill/klipper-led_effect |        |
+| HEAT     | Lights up or flashes according to the heating PWM            |        |
+
+| LED name | Indicate                                                     | Remark |
+| -------- | ------------------------------------------------------------ | ------ |
+| 3V3      | 亮：电源正常。 <br/>灭：电源故障。3.3V是由24V经过DC-DC转5V再经过LDO转3.3V得来的，所以可能24V/5V/3.3V出现了短路/断路之类的不良。 |        |
+| HUB      | 亮：USB至少有一个连接。<br/>灭：USB没有任何连接。            |        |
+| STATUS   | 在使用 katakulpt时<br>闪烁：进入下载模式；<br>灭/常亮：非下载模式，此时状态一般是由config所决定；<br>该LED由PC13控制，高电平点亮，自定义用法可参考[julianschill/klipper-led_effect](https://github.com/julianschill/klipper-led_effect) |        |
+| HEAT     | 根据加热的PWM亮灭或者闪烁                                    |        |
+
+## CAN / USB Switcher 
+
+![img](images/SB_Combo_V2/SB_Combo_V2_switcher.png)
+- 如图所示，绿色标记拨动开关负责输入CAN / USB切换，处于XT30连接器上；
+- 橙色标记拨动开关负责标记为USB2的连接器（MX1.25-4P）处 CAN / USB切换。
+- As shown in the figure, the green-marked toggle switch is responsible for the input CAN/USB switching, which is located on the XT30 connector; the orange-marked toggle - switch is responsible for the CAN/USB switching at the connector marked as USB2 (MX1.25-4P).
+
+## Jumpers：![image-20240902163114843](images/SB_Combo_V2/SB_Combo_V2_jumpers.png)
+IO.0+1和IO.2可以通过跳线帽进行供电电压选择，如图所示，左侧两个Pin连接在一起为5V，右侧两个Pin连接在一起为24V。
+
+IO.0+1 and IO.2 can select the power supply voltage through the jumper cap. As shown in the figure, the two pins on the left are connected together for 5V, and the two pins on the right are connected together for 24V.
+
+## Input/Output：
+
+描述各个预留IO的输入输出能力，ADC / PWM / SCL / SPI等通信
+
+## Power distribution：
+
+- VIN
+- 24V
+- 12V
+- 5V
+- 3.3V
+> [!Note]
+
+## 连接到树莓派
+
+### 通过USB
+
+### 通过CAN
+##### Via UCAN
+##### Via MainBoard
+
+##### Native CAN of CM68
+
+## 连接风扇
+
+2线/3线/4线
+
+## 连接温度传感器
+
+热敏电阻
+
+ PT1000 
+
+## 连接电机
+
+## 其他连接
+
+接近开关 
+
+Klicky
+
+TAP
+
+# 固件向导
+
+## 固件配置和编译
+
+### Katapult Bootloader
+![SB_Combo_V2_katakulpt_menuconfig_8k_CAN](images/SB_Combo_V2/SB_Combo_V2_katakulpt_menuconfig_8k_CAN.png)
+![SB_Combo_V2_katakulpt_menuconfig_8k_USB](images/SB_Combo_V2/SB_Combo_V2_katakulpt_menuconfig_8k_USB.png)
+
+### Klipper
+
+  ![SB_Combo_V2_menuconfig_8k_CAN](images/SB_Combo_V2/SB_Combo_V2_menuconfig_8k_CAN.png)
+
+  ![SB_Combo_V2_menuconfig_8k_USB](images/SB_Combo_V2/SB_Combo_V2_menuconfig_8k_USB.png)
+
+  ![SB_Combo_V2_menuconfig_nobootloader_CAN](images/SB_Combo_V2/SB_Combo_V2_menuconfig_nobootloader_CAN.png)
+
+  ![SB_Combo_V2_menuconfig_nobootloader_USB](images/SB_Combo_V2/SB_Combo_V2_menuconfig_nobootloader_USB.png)
+
+## 固件上传
+
+# FAQ
+
+# 附件及其他
+
+  - [尺寸：2D，3D ](https://github.com/FYSETC/SB_Combo_V2/blob/main/3D/SB_Combo_V2.step)
+  - 安装示例：支架（STL）
+  - 散热：推荐的通风方式
+  - 温度：MCU，驱动，电源
+
+# 如何购买
+
+淘宝，速卖通，亚马逊，官网
+
+# 技术支持通道
+
+FB / Discord / Forum