Debugging G2 on OSX with GDB and Atmel ICE

See also: Compiling G2 on OSX with Xcode ##Hardware Required You will need the following hw and configuration

• TinyGv9 board
• Atmel-ICE debugger
• Both plugged into an OSX machine via USB, preferably without a hub. See the [Apple] / About this Mac / More Info / System Report / USB section. Hit command R if you want to refresh. Some times getting these connected takes some unplugging and replugging to get USB to behave.

##Install OpenOCD Debugger

1. Install hombrew: http://brew.sh/ Look for "Install Homebrew” near the bottom of that page. Follow those instructions in Terminal.
   

ruby -e "$(curl -fsSL https://raw.githubusercontent.com/Homebrew/install/master/install)"

As instructed, run brew doctor before you install anything, and install the Command Line Tools for Xcode: https://developer.apple.com/downloads. Search "Command Line Tools for Xcode". You may need to register as an Apple Developer for this step. You can also run this command in terminal to install Xcode Command Line Tools: xcode-select --install (and select Install in the popup window).

2. In terminal, run:
   brew install openocd

3. cd into the /TinyG2/ directory, have the V9 all wired up and run:
   make VERBOSE=2 PLATFORM=G2v9i debug

That should have you debugging in gdb. If you get connection errors make sure the Atmel-ICE is connected as in Hardware, above.

On OSX it might pop a dialog box requesting you to accept an inbound connection. Do it. You may also need to try to connect more than once for it to work.

##Using GDB

• References:

  • GDB reference manual
  • GDB cheat sheet

• Some useful commands

  • monitor reset halt to reset
  • monitor load programs the board with the current elf

• The make command sets the "current elf"

• This is Embedded GDB, so some commands in the cheat sheets do not work:

  • run

Debugging and loading

In order to debug you need a debugger capable of debugging the chip you use. For the Due and V9 we use either a Atmel SAM-ICE (which is a OEM Segger J-Link locked to Atmel ARMs) or the cheaper and more recently released Atmel ICE. Either can be found at Mouser.com.

You choose which debug adapter you wish to use by copying the openocd.cfg.example file to openocd.cfg and then editing the openocd.cfg file. Simply follow the instructions in that file. Hint: It's just uncommenting the correct lines.

Once that is configured, you'll need to make sure the debugger is correctly connected to the hardware and plugged into the computer, and all of the hardware is powered properly.

Then call make debug - don't forget to include any of the additional variables on your make command line, or it may build for the wrong platform. A few eaxmples:

# If you normally call this to build:
make PLATFORM=UltimakerTests SETTINGS_FILE=my_settings.h

# Then just add the "debug" to the end
make PLATFORM=UltimakerTests SETTINGS_FILE=my_settings.h debug

This will build the code (if it needs it) and then open gdb connected to the hardware and reset and halt the TinyG2 system.

A Very Brief Embedded GDB primer

Even if you are familiar with GDB, you may find a few important differences when using it with an embedded project. This will not be a thorough how-to on this topic, but will hopefully serve enough to get you started.

Using make debug will call gdb (technically it's arm-none-eabi-gdb or whatever variant is specified in the makefile for your board, but we'll just call it gdb from now on) with parameters and configuration to:

• Know which binary/elf file to use for this debug session.
• Connect to the board using openocd.
• And halt the board, and leave you at a command line prompt.

Now for a few commands to get you started:

Flashing the firmware onto the board

load - Since gdb already knows what bianry/elf file to use, you simple have to type load at the (gdb) prompt. Here's an example of a succesful flash session:

(gdb) load
Loading section .text, size 0x1da10 lma 0x80000
Loading section .relocate, size 0x164 lma 0x9da10
Start address 0x82c88, load size 121716
Transfer rate: 14 KB/sec, 13524 bytes/write.
(gdb)

Resetting the processor

monitor reset halt - Once we flash new code, or if we just want the "program" to start over, we call monitor reset halt to reset and halt the processor. This will freeze the processor at the reset state, before any code has executed.

You must call monitor reset halt after (or immediately before) a load command so that the processor starts from the new code. Otherwise, the processor will likely crash, sometimes after appearing to work for some time. To avoid nightmare debug sessions, be sure you always follow load with monitor reset halt!

Quitting the debugger

q or quit will exit GDB. If the processor is running, you may need to type CTRL-C to get the prompt first.

You will often need to reset or power-cycle the board after quitting GDB, since it will likely leave it in a halt state.

Running the code

Full docs are here for continue, step, and next.

c or continue - To resume the processor operating normally, you type c (or the full word continue) and hit return.

Once it's running, gdb will not show a prompt, and you cannot see any output from the processor. To pause the processor again, hit CTRL-C.

NOTE: If you are used to using gdb in a desktop OS, you will notice that we didn't call run -- in fact, it won't work. In embedding programming, you're driving the whole OS on the processor, not just running a single program.

Step to the next line (into or over functions)

s or step - Continue running your program until control reaches a different source line, then stop it and return control to GDB. This will step into functions, since that would change which line is being executed.

n or next - Continue to the next source line in the current (innermost) stack frame. This will skip over function calls, since that would change which stack frame is executing.

fin or finish - Continue running until just after function in the selected stack frame returns. Print the returned value (if any).

Getting a backtrace (listing the function call stack)

Full documentation is here for bt and related.

bt or backtrace - Print a backtrace of the entire stack: one line per frame for all frames in the stack. (Note that this may get LONG, and you can make it stop with CTRL-C.)

Example:

(gdb) bt
#0  0x00085df2 in _controller_HSM () at ./controller.cpp:172
#1  controller_run () at ./controller.cpp:150
#2  0x000889fc in main () at ./main.cpp:169

Note that the current execution frame is on the top, and main() is on the bottom.

Interpretation: main() called controller_run(), which called _controller_HSM(), which is where we are "currently." It also tells us that that is specifically at line 172 of ./controller.cpp.

These are more advanced topics covered very well all over the internet, so I won't go into detail here. I will list a few usefull commands to start of your research, however:

Breakpoints

Documented here.

• b -- set a breakpoint. Will default to "here" but you can pass it a function name or a filename:line to break on a specific line.
• info b -- show breakpoints.

Showing Variables

Documented here

• p expression - execute the given expression and print the results. Takes most C syntax (but not all) in the expression. Warning! It is a common mistake to accidentally change the state or variables when trying to display them. For example, this is a terrible way to test if the should_blow_up variable is true:

    (gdb) p should_blow_up=1
    $1 = 1 '\001'

  It will actually set should_blow_up to true!! A check, like normal C, would be with the double equals:

   (gdb) p should_blow_up==1
   $2 = false

  p will also nicely print out entire structures. You may have to dereference pointers, however:

   (gdb) p mb.r
   $4 = (mpBuf_t *) 0x20071434 <mb+220>
   (gdb) p *mb.r
   $5 = {
   	pv = 0x20071368 <mb+16>,
   	nx = 0x20071500 <mb+424>,
   	# ... clipped some for brevity ...
   	jerk = 0,
   	recip_jerk = 0,
   	cbrt_jerk = 0,
   	gm = {
   		linenum = 0,
   		motion_mode = 0 '\000',
   		# ... clipped some for brevity ...
   		spindle_mode = 0 '\000'
   	}
   }
   (gdb)