Saltwater cell - 0%-> programmed % -> 0% (bouncing) when AqualinkD service is started

[igorek24]

My Jendy AquaPure SWG keeps turning on and off when AqualinkD service is running and the only way to make it work is ether disconnect it from RS285 or shutdown AqualinkD. I tried to set the read_RS485_swg to yes/no as well as force_SWG yes/no/comment it out and nothing helps.
Here is my output from the logger:

`AqualinkD serial_logger V1.4
Notice: RS Serial: Logging serial information!
Please wait.|

Notice: RS Serial: RS485 interface received 2000 packets in 42 seconds (~47.62 Msg/Sec)
Notice: RS Serial: Jandy Control Panel Model : RS-8 Combo
Notice: RS Serial: Jandy Control Panel Version : REV T.2
Notice: RS Serial: Jandy ID's found
Notice: RS Serial: ID 0x33 is in use <-- Aqualink (iAqualink / Touch)
Notice: RS Serial: ID 0xa3 is in use <-- Unknown Device
Notice: RS Serial: ID 0x50 is in use <-- Salt Water Generator (Aquarite mode)
Notice: RS Serial: ID 0x60 is not used <-- can use for Aqualinkd (PDA mode only)
Notice: RS Serial: ID 0x08 is not used <-- can use for Aqualinkd
Notice: RS Serial: ID 0x0a is not used <-- can use for Aqualinkd
Notice: RS Serial: ID 0x0b is not used <-- can use for Aqualinkd
Notice: RS Serial: ID 0x40 is not used <-- can use for Aqualinkd (Extended Device ID)
Notice: RS Serial: ID 0x41 is not used <-- can use for Aqualinkd (Extended Device ID)
Notice: RS Serial: ID 0x42 is not used <-- can use for Aqualinkd (Extended Device ID)
Notice: RS Serial: ID 0x43 is not used <-- can use for Aqualinkd (Extended Device ID)
Notice: RS Serial: ID 0x30 is not used <-- can use for Aqualinkd (Prefered Extended Device ID)
Notice: RS Serial: ID 0x31 is not used <-- can use for Aqualinkd (Prefered Extended Device ID)
Notice: RS Serial: ID 0x32 is not used <-- can use for Aqualinkd (Prefered Extended Device ID)
Notice: RS Serial: ID 0x48 is not used <-- can use for Aqualinkd (RSSA ID)
Notice: RS Serial: ID 0x09 is not used <-- can use for Aqualinkd
Notice: RS Serial:

Notice: RS Serial: Pentair ID's found
Notice: RS Serial: ID 0x10 is in use <-- Pentair Master (Probably Jandy RS Control Panel)
Notice: RS Serial: ID 0x60 is in use <-- Pentair VSP
Notice: RS Serial: `

and Here is my config:

`web_directory=/var/www/aqualinkd/

log_file=/var/log/aqualinkd.log

log_level=DEBUG

display_warnings_in_web=true

socket_port=8081

serial_port=/dev/ttyS2

device_id=0x0a

rssa_device_id=0x48

extended_device_id=0x31

extended_device_id_programming = yes

read_RS485_swg = no
read_RS485_ePump = no
read_RS485_vsfPump = yes

keep_paneltime_synced = yes

override_freeze_protect = no

convert_mqtt_temp_to_c = no
convert_dz_temp_to_c = no

report_zero_spa_temp = yes

report_zero_pool_temp = yes

mqtt_address =
mqtt_user =
mqtt_passwd =
mqtt_aq_topic =

force_SWG = yes

light_programming_mode=0.6

light_programming_initial_on=15

light_programming_initial_off=12

use_panel_aux_labels=no

button_01_label=Filter Pump
button_01_pumpID=0x60
button_01_pumpIndex=1

button_02_label=Spa Mode

button_03_label=Spa Jets

button_04_label=Waterfall

button_05_label=Spa Light

button_06_label=Pool Light
#button_05_lightMode=0

button_07_label=Cleaner
#button_05_lightMode=0

button_08_label=NONE

button_09_label=NONE

button_10_label=Pool Heater

button_11_label=Spa Heater

button_12_label=Solar Heater`