Version: 1.4.0
Last Updated: 11 November, 2023
See the file COPYING for license.
Symon is a general purpose simulator for systems based on the MOS Technologies 6502 microprocessor and compatibles. Symon is implemented in Java. Its core goals are accuracy, ease of development, clear documentation, and extensive test suites for validating correctness.
Symon simulates a complete system with a 1 MHz NMOS 6502 or CMOS 65C02, 32KB of RAM, 16KB of ROM, a MOS 6551 or Motorola 6850 ACIA, a MOS 6522 VIA, and an experimental 6545 CRTC.
Symon has extensive unit tests to verify correctness, and fully passes Klaus Dormann's 6502 Functional Test Suite as of version 0.8.2 (See this thread on the 6502.org Forums for more information about this functional test suite).
Symon is under active maintenance. Feedback and patches are always welcome.
- Java 1.8 or higher
- Maven 2.0.x or higher (for building from source)
- JUnit 4 or higher (for testing)
Symon can simulate multiple 6502 based architectures. At present, four machines are implemented: Symon (the default), MULTICOMP, BenEater, and a "Simple" machine useful for debugging.
$0000--$7FFF: 32KB RAM$8000--$800F: 6522 VIA$8800--$8803: MOS 6551 ACIA (Serial Console)$9000--$9001: MOS 6545 CRTC$C000--$FFFF: 16KB ROM
The CRT Controller uses memory address $7000 as the start of Video
memory.
$0000--$DFFF: 56KB RAM$E000--$FFFF: 8KB ROM$FFD0--$FFD1: Motorola 6850 ACIA$FFD8--$FFDF: Controller for SD cards
$0000--$FFFF: 64KB RAM
$0000--$3FFF: 16KB RAM$5000--$5003: MOS 6551 ACIA (Serial Console)$6000--$600F: 6522 VIA$8000--$FFFF: 16KB ROM
The main window of the simulator acts as the primary Input/Output system through a virtual serial terminal. It also provides CPU status. Contents of the accumulator, index registers, processor status flags, disassembly of the instruction register, and stack pointer are all displayed.
The terminal is attached to a simulated MOS 6551 ACIA. It behaves very much as described in the datasheet, with some exceptions:
- The simulated ACIA is permanently connected to the virtual terminal, the Data Carrier Detect and Data Set Ready status bits always indicate a connection is ready.
- The parity, stop-bits and bits-per-character settings are ignored. The ACIA always sends and receives 8-bit characters, and parity errors do not occur.
- The ACIA tries to honour the configured baud rate, but as a special case the default "16x External Clock" rate is interpreted to mean "as fast as possible" (The sample Enhanced BASIC ROM image is programmed for 9600 baud).
- The ACIA ignores the configured state of the Data Terminal Ready pin; it is always ready to receive and transmit.
For more information on the MOS 6551 ACIA and its programming model, see the official datasheet:
The console supports font sizes from 10 to 20 points.
Symon can load any appropriately sized ROM image. The Symon architecture expects as 16KB (16384 byte) ROM image, while the MULTICOMP architecture expects an 8KB (8192 byte) ROM image. Images are loaded via the "Load ROM..." action in the "File" menu. The selected ROM file will be loaded into memory at the correct ROM base address.
Memory contents can be viewed (and edited) one page at a time through the Memory Window.
The last 20,000 execution steps are disassembled and logged to the Trace Log Window.
Simulated speeds may be set from 1MHz to 8MHz.
Breakpoints can be set and removed through the Breakpoints window.
This feature is highly experimental. It's possible to open a video window
from the "View" menu. This window simulates the output of a MOS 6545 CRT
Controller located at address $9000 and $9001.
By default, the 40 x 25 character display uses video memory located at base
address $7000. This means that the memory from address $7000 (28672
decimal) to $73E8 (29672 decimal) is directly mapped to video.
- Address Register (at address
$9000) - R1: Horizontal Displayed Columns
- R6: Vertical Displayed Rows
- R9: Scan Lines per Row
- R10: Cursor Start Scan Line and Cursor Control Mode
- R11: Cursor End Scan Line
- R12: Display Start Address (High Byte)
- R13: Display Start Address (Low Byte)
- R14: Cursor Position (High Byte)
- R15: Cursor Position (Low Byte)
Although the simulation is pretty good, there are a few key differences between the simulated 6545 and a real 6545:
-
The simulated 6545 supports only the straight binary addressing mode of the real 6545, and not the Row/Column addressing mode.
-
The simulated 6545 has full 16 bit addressing, where the real 6545 has only a 14-bit address bus.
-
The simulation is done at a whole-frame level, meaning that lots of 6545 programming tricks that were achieved by updating the frame address during vertical and horizontal sync times are not achievable. There is no way (for example) to change the Display Start Address (R12 and R13) while a frame is being drawn.
For more information on the 6545 CRTC and its programming model, please see the following resources
This program will fill the video screen with all printable characters.
10 J = 0
20 FOR I = 28672 TO 29672
30 POKE I,J
40 IF J < 255 THEN J = J + 1 ELSE J = 0
50 NEXT I
60 END
To build Symon with Apache Maven, just type:
$ mvn package
Maven will build Symon, run unit tests, and produce a jar file in the
target directory containing the compiled simulator.
Symon is meant to be invoked directly from the jar file. To run with Java 1.8 or greater, just type:
$ java -jar symon-1.2.0.jar
When Symon is running, you should be presented with a simple graphical interface.
Two command line options may be passed to the JAR file on startup, to specify machine type and CPU type. The options are:
-c,-cpu 6502: Use the NMOS 6502 CPU type by default.-c,-cpu 65c02: Use the CMOS 65C02 CPU type by default.-c,-machine symon: Use the Symon machine type by default.-c,-machine multicomp: Use the Multicomp machine type by default.-m,-machine simple: Use the Simple machine type by default.-m,-machine beneater: Use the BenEater machine type by default.-r,-rom <file>: Use the specified file as the ROM image.-b,-brk: Halt the simulator on a BRK instruction (default is to continue)
The simulator requires a ROM image loaded into memory to work properly. Without a ROM in memory, the simulator will not be able to reset, since the reset vector for the 6502 is located in the ROM address space.
ROM images can be loaded with the -rom argument when running
Symon from the command line. ROM images can also be swapped out at
run-time with the "Load ROM..." item in the File menu.
The "samples" directory contains a ROM image for the Symon architecture named 'ehbasic.rom', containing Lee Davison's Enhanced 6502 BASIC. This serves as a good starting point for exploration.
Note: Presently, EhBASIC only works with the Symon machine architecture, not with MULTICOMP.
In addition to ROM images, programs in the form of raw binary object files can be loaded directly into memory from "Load Program..." in the File menu.
Programs are loaded starting at addres $0300. After loading the program, the simulated CPU's reset vector is loaded with the values $00, $03, and the CPU is reset.
There are two very simple sample program in the "samples" directory, for testing.
-
'echo.prg' will echo back anything typed at the console.
-
'hello.prg' will continuously print "Hello, 6502 World!" to the console.
After loading a program or ROM image, clicking "Run" will start the simulator running.
-
1.4.0: 11 November 2023 - Adds a new machine, the Ben Eater machine. Correct handling of 6551 interrupts, and several 6551 bug fixes. Fixes power-on status of 6502 status register. Fixes a bug with ASCII backspace character not moving the cursor backwards. Finally, "halt on BRK" is no longer enabled by default, but can be set at runtime or by a command line flag. Thank you to Tim Allen and Chelsea Wilkinson for contributions!
-
1.3.2: 8 March 2022 - Minor bug fixes.
-
1.3.1: 12 October, 2019 - Add support for new command line option
-cpu <type>to specify one of6502or65c02on startup, and new option-rom <file>to specify a ROM file to load. -
1.3.0: 24 February, 2018 - Adds support for 65C02 opcodes.
-
1.2.1: 8 January, 2016 - Remove dependency on Java 8. Now supports compiling and running under Java 1.7.
-
1.2.0: 3 January, 2016 - Add symbolic disassembly to breakpoints window.
-
1.1.1: 2 January, 2016 - Minor enhancement: Allows breakpoints to be added with the Enter key.
-
1.1.0: 31 December, 2015 - Fixed delay loop to better simulate various clock speeds. Added ability to select clock speed at runtime. Status display now shows the next instruction to be executed, instead of the last instruction executed. Added support for breakpoints.
-
1.0.0: 10 August, 2014 - Added "Simple" machine implementation, pure RAM with no IO. Added Klaus Dormann's 6502 Functional Tests for further machine verification (these tests must be run in the "Simple" machine).
-
0.9.9.1: 27 July, 2014 - Pressing 'Control' while clicking 'Reset' now performs a memory clear.
-
0.9.9: 26 July, 2014 - MULTICOMP and multi-machine support contributed by Maik Merten <[email protected]>
-
0.9.1: 26 January, 2014 - Support for IRQ and NMI handling.
-
0.9.0: 29 December, 2013 - First pass at a 6545 CRTC simulation.
-
0.8.5: 30 March, 2013 - ASCII display for memory window. Allows user to select a step count from a drop-down box.
-
0.8.4: 4 March, 2013 - Fix for ZPX, ZPY display in the trace log (change contributed by jsissom)
-
0.8.3: 12 January, 2013 - Added tool-tip text. Memory is no longer cleared when resetting. Fixed swapped register labels.
-
0.8.2: 01 January, 2013 - Fully passes Klaus Dormann's 6502 Functional Test suite!
-
0.8.1: 30 December, 2012
-
0.8.0: 29 December, 2012
-
0.7.0: 9 December, 2012
-
0.6: 5 November, 2012
-
0.5: 21 October, 2012 - Able to run Enhanced BASIC for the first time.
-
0.3: 14 October, 2012
-
0.2: 22 April, 2012
-
0.1: 20 January, 2010
-
1.2: Better breakpoint support. Symbolic debugging of breakpoints.
-
2.0: Complete rewrite of the UI in JavaFX instead of Swing. Complete assembler and disassembler built in. Ability to attach source code for symbolic debugging.
-
Feedback (in the form of dialogs, status bar, etc).
-
Better debugging tools from the UI, including breakpoints and disassembly.
-
UI needs a ton more polish.
-
More extensive testing.
-
Clean up JavaDoc.
-
Implement CMOS 65C02 instructions and NMOS / CMOS mode flag.
-
Allow displaying ACIA status and dumping ACIA buffers, for debugging.
-
CRTC emulation is very naive. The whole frame is drawn in one CPU step. This should be improved by drawing scan lines during machine steps to approximate real NTSC/PAL refresh rates.
-
Symbolic debugging.
Copyright (c) 2014 Seth J. Morabito <[email protected]>
- Portions Copyright (c) 2014 Maik Merten <[email protected]>
- Portions Copyright (c) 2022 Tim Allen <[email protected]>
- Portions Copyright (c) 2023 Chelsea Wilkinson <[email protected]>
Additional components used in this project are copyright their respective owners.
- Enhanced 6502 BASIC Copyright (c) Lee Davison
- 6502 Functional Tests Copyright (c) Klaus Dormann
- JTerminal Copyright (c) Graham Edgecombe
This project would not have been possible without the following resources:
-
Andrew Jacobs' 6502 Pages, for wonderfully detailed information about the 6502
-
Neil Parker's "The 6502/65C02/65C816 Instruction Set Decoded", for information about how instructions are coded
Symon is free software. It is distributed under the MIT License. Please see the file 'COPYING' for full details of the license.