diff --git a/README.md b/README.md
index 6b7c6f1..9558f9d 100644
--- a/README.md
+++ b/README.md
@@ -10,7 +10,7 @@ The [MHINSTEK_MHS-5200A](https://sigrok.org/wiki/MHINSTEK_MHS-5200A "MHINSTEK_MH
 
 
 Installation
------------
+------------
 
 [Install golang](https://golang.org/doc/install)
 
@@ -23,12 +23,149 @@ make
 The compiled binary can be found in the bin folder.
 
 Quick start
-----------
+-----------
 
 ```
 ./bin/mhs5200a
+
+Usage: mhs5200a [options] [command]...
+
+options can be zero or more of the following:
+  -port string
+    	port the MHS-5200A is connected to (default "/dev/ttyUSB0")
+  -script string
+    	json script file
+  -v int
+    	verbose level
+
+command can be one or more of the following:
+  showconfig - show the configuration of the current channel
+  on - turn output on
+  off - turn output off
+
+  channel [1|2] - sets the channel number commands will apply to
+  frequency N - set the frequency N Hz
+  waveform name - set the waveform to name. Valid names are sine, square, triangle, rising sawtooth, descending sawtooth
+  amplitude N - set the amplitude to N Volts
+  duty N - set the duty cycle to N%
+  offset N - set the DC offset to N% of the amplitude. Valid range is -120% to +120%
+  phase N - set the phase to N°
+  attenuation [on|off] - configure -20dB channel attenuation
+
+  showsweep - show the current sweep mode configuration
+  sweepstart N - set the sweep start frequenecy to N Hz
+  sweepend N - set the sweep end frequenecy to N Hz
+  sweepduration N - set the sweep duration to N secs
+  sweeptype [log|linear] - set the sweep type to either log or linear
+  sweepon - turn sweep function on
+  sweepoff - turn sweep function off
+
+  sleep N - delay N seconds before executing the next command
+  delay N - delay N seconds before executing the next command
+
+  save N - save current configuration to slot N
+  load N - load current configuration from slot N
+
+Examples:
+mhs5200a channel 2 frequency 10000 phase 180 waveform square duty 33.25 attenuation off showconfig on sleep 120 off
+mhs5200a sweepstart 10 sweepend 100000 sweepduration 60 sweetype linear showsweep sweepon delay 60 sweepoff
+mhs5200a save 10
+mhs5200a load 10
 ````
-will display some brief usage instructions.
+
+Scripting
+---------
+
+mhs5200a supports rudimentary scripting by leveraging the JSON format. This allows storing frequently used setups on the host computer and not relying on the instrument's internal save/load slots.
+
+In essence the json format encapsulates a sequence of commands into a JSON array called cmds and plays them back in sequence. In turn each cmd block contains a data array which encapsulates the configuration for that command.
+A list of available commands is show below:
+````
+config
+showconfig
+delay
+sleep
+on
+off
+save
+load
+showsweep
+configsweep
+sweepon
+sweepoff
+````
+A list of available parameters that can be specified in the data array are show below:
+````
+channel
+frequency
+waveform
+amplitude
+phase
+duty
+offset
+attenuation
+seconds
+slot
+startf
+endf
+type
+````
+A list of supported values for the waveform parameter are shown below:
+````
+sine
+square
+triangle
+rising sawtooth
+descending sawtooth
+````
+Let's look at a brief example
+````JSON
+{
+    "cmds" : [
+        { "cmd" : "config", "data" : [ { "channel" : 1, "frequency" : 1.0e03, "waveform" : "square", "amplitude" : 5.0, "phase" : 0.0, "duty" : 50.0, "attenuation" : false } ] },
+        { "cmd" : "showconfig", "data" : [ { "channel" : 1 } ] }
+    ]
+}
+````
+The first line, cmd config, configures channel 1 for a frequency of 1KHz, a square waveform, an amplitude for 5.0V, a phase angle of 0 degrees, a 50% duty cycle and turns off the -20dB attenuation.
+The second line simply dumps the configuration for channel 1.
+
+Here is another more complicated example, that shows most of the commands available
+````JSON
+{
+    "cmds" : [
+        { "cmd" : "config", "data" : [ { "channel" : 1, "frequency" : 25e03, "waveform" : "square", "amplitude" : 5.0, "phase" : 90.0, "duty" : 33.3, "attenuation" : false } ] },
+        { "cmd" : "on", "data" : [ { "channel" : 1 } ] },
+        { "cmd" : "showconfig", "data" : [ { "channel" : 1 } ] },
+        { "cmd" : "delay", "data" : [ { "seconds" : 15 } ] },
+        
+        { "cmd" : "config", "data" : [ { "channel" : 1, "frequency" : 50e03, "waveform" : "sine", "amplitude" : 3.3, "phase" : 180.0, "duty" : 50.0, "attenuation" : false } ] },
+        { "cmd" : "showconfig", "data" : [ { "channel" : 1 } ] },
+        { "cmd" : "delay", "data" : [ { "seconds" : 15 } ] },
+        
+        { "cmd" : "config", "data" : [ { "channel" : 1, "frequency" : 55e03, "waveform" : "triangle", "amplitude" : 5.0, "phase" : 0.0, "duty" : 75.0, "attenuation" : false } ] },
+        { "cmd" : "showconfig", "data" : [ { "channel" : 1 } ] },
+        { "cmd" : "delay", "data" : [ { "seconds" : 15 } ] },
+        
+        { "cmd" : "config", "data" : [ { "channel" : 1, "frequency" : 60e03, "waveform" : "rising sawtooth", "amplitude" : 5.0, "phase" : 0.0, "duty" : 50.0, "attenuation" : false } ] },
+        { "cmd" : "showconfig", "data" : [ { "channel" : 1 } ] },
+        { "cmd" : "delay", "data" : [ { "seconds" : 15 } ] },
+        
+        { "cmd" : "config", "data" : [ { "channel" : 1, "frequency" : 65e03, "waveform" : "descending sawtooth", "amplitude" : 5.0, "phase" : 0.0, "duty" : 50.0, "attenuation" : false } ] },
+        { "cmd" : "showconfig", "data" : [ { "channel" : 1 } ] },
+        { "cmd" : "delay", "data" : [ { "seconds" : 15 } ] },
+        
+        { "cmd" : "configsweep", "data" : [ { "startf" : 1e03, "endf" : 100e03, "seconds" : 10, "type" : "log", "waveform": "square", "duty" : 50.0 } ] },
+        { "cmd" : "showsweep" },
+        { "cmd" : "sweepon" },
+        { "cmd" : "delay", "data" : [ { "seconds" : 10 } ] },
+        { "cmd" : "sweepoff" },
+        
+        { "cmd" : "off", "data" : [ { "channel" : 1 } ] }
+    ]
+}
+````
+
 
 Contact
 -------