This section is a modified version of http://en.wikipedia.org/wiki/Initrd which is licensed under the Creative Commons Attribution/Share-Alike License.
An initial ramdisk is a temporary file system used in the boot process of the Linux kernel. initrd and initramfs refer to slightly different schemes for loading this file system into memory. Both are commonly used to make preparations before the real root file system can be mounted.
Many Linux distributions ship a single, generic kernel image that is intended to boot as wide a variety of hardware as possible. The device drivers for this generic kernel image are included as loadable modules, as it is not possible to statically compile them all into the one kernel without making it too large to boot from computers with limited memory or from lower-capacity media like floppy disks.
This then raises the problem of detecting and loading the modules necessary to mount the root file system at boot time (or, for that matter, deducing where or what the root file system is).
To further complicate matters, the root file system may be on a software RAID volume, LVM, NFS (on diskless workstations), or on an encrypted partition. All of these require special preparations to mount.
Another complication is kernel support for hibernation, which suspends the computer to disk by dumping an image of the entire system to a swap partition or a regular file, then powering off. On next boot, this image has to be made accessible before it can be loaded back into memory.
To avoid having to hardcode handling for so many special cases into the kernel, an initial boot stage with a temporary root file system —now dubbed early user space— is used. This root file system would contain user-space helpers that would do the hardware detection, module loading and device discovery necessary to get the real root file system mounted.
An image of this initial root file system (along with the kernel image) must be stored somewhere accessible by the Linux bootloader or the boot firmware of the computer. This can be:
-
The root file system itself
-
A boot image on an optical disc
-
A small ext2/ext3/ext4 or FAT-formatted partition on a local disk (a boot partition)
-
A TFTP server (on systems that can boot from Ethernet)
The bootloader will load the kernel and initial root file system image into memory and then start the kernel, passing in the memory address of the image.
Depending on which algorithms were compiled statically into it, the kernel can currently unpack initrd/initramfs images compressed with gzip, bzip2 and LZMA.
dracut can generate a customized initramfs image which contains only whatever is necessary to boot some particular computer, such as ATA, SCSI and filesystem kernel modules (host-only mode).
dracut can also generate a more generic initramfs image (default mode).
dracut’s initramfs starts only with the device name of the root file system (or its UUID) and must discover everything else at boot time. A complex cascade of tasks must be performed to get the root file system mounted:
-
Any hardware drivers that the boot process depends on must be loaded. All kernel modules for common storage devices are packed onto the initramfs and then udev pulls in modules matching the computer’s detected hardware.
-
On systems which display a boot rd.splash screen, the video hardware must be initialized and a user-space helper started to paint animations onto the display in lockstep with the boot process.
-
If the root file system is on NFS, dracut does then:
-
Bring up the primary network interface.
-
Invoke a DHCP client, with which it can obtain a DHCP lease.
-
Extract the name of the NFS share and the address of the NFS server from the lease.
-
Mount the NFS share.
-
-
If the root file system appears to be on a software RAID device, there is no way of knowing which devices the RAID volume spans; the standard MD utilities must be invoked to scan all available block devices with a raid signature and bring the required ones online.
-
If the root file system appears to be on a logical volume, the LVM utilities must be invoked to scan for and activate the volume group containing it.
-
If the root file system is on an encrypted block device:
-
Invoke a helper script to prompt the user to type in a passphrase and/or insert a hardware token (such as a smart card or a USB security dongle).
-
-
Create a decryption target with the device mapper.
dracut uses udev, an event-driven hotplug agent, which invokes helper programs as hardware devices, disk partitions and storage volumes matching certain rules come online. This allows discovery to run in parallel, and to progressively cascade into arbitrary nestings of LVM, RAID or encryption to get at the root file system.
When the root file system finally becomes visible:
-
Any maintenance tasks which cannot run on a mounted root file system are done.
-
The root file system is mounted read-only.
-
Any processes which must continue running (such as the rd.splash screen helper and its command FIFO) are hoisted into the newly-mounted root file system.
The final root file system cannot simply be mounted over /, since that would make the scripts and tools on the initial root file system inaccessible for any final cleanup tasks. On an initramfs, the initial root file system cannot be rotated away. Instead, it is simply emptied and the final root file system mounted over the top.
If the systemd module is used in the initramfs, the ordering of the services started looks like [dracutbootup7].
On a systemd driven system, the dracut initramfs is also used for the shutdown procedure.
The following steps are executed during a shutdown:
-
systemd switches to the shutdown.target
-
systemd starts $prefix/lib/systemd/system/shutdown.target.wants/dracut-shutdown.service
-
dracut-shutdown.service executes /usr/lib/dracut/dracut-initramfs-restore which unpacks the initramfs to /run/initramfs
-
systemd finishes shutdown.target
-
systemd kills all processes
-
systemd tries to unmount everything and mounts the remaining read-only
-
systemd checks, if there is a /run/initramfs/shutdown executable
-
if yes, it does a pivot_root to /run/initramfs and executes ./shutdown. The old root is then mounted on /oldroot. /usr/lib/dracut/modules.d/99shutdown/shutdown.sh is the shutdown executable.
-
shutdown will try to unmount every /oldroot mount and calls the various shutdown hooks from the dracut modules
This ensures, that all devices are disassembled and unmounted cleanly.
This work is licensed under the Creative Commons Attribution/Share-Alike License. To view a copy of this license, visit http://creativecommons.org/licenses/by-sa/3.0/ or send a letter to Creative Commons, 559 Nathan Abbott Way, Stanford, California 94305, USA.