Add stm32u575-nucleo support

hw/bsp/stm32u5/boards/stm32u575eval/board.mk

@@ -2,7 +2,7 @@ CFLAGS += \
   -DSTM32U575xx \
 
 # All source paths should be relative to the top level.
-LD_FILE = $(BOARD_PATH)/STM32U575AIIXQ_FLASH.ld
+LD_FILE = ${ST_CMSIS}/Source/Templates/gcc/linker/STM32U575xx_FLASH.ld
 
 SRC_S += $(ST_CMSIS)/Source/Templates/gcc/startup_stm32u575xx.s
 

hw/bsp/stm32u5/boards/stm32u575nucleo/board.cmake

@@ -0,0 +1,10 @@
+set(MCU_VARIANT stm32u575xx)
+set(JLINK_DEVICE stm32u575zi)
+
+set(LD_FILE_GNU ${ST_CMSIS}/Source/Templates/gcc/linker/STM32U575xx_FLASH.ld)
+
+function(update_board TARGET)
+  target_compile_definitions(${TARGET} PUBLIC
+    STM32U575xx
+    )
+endfunction()

hw/bsp/stm32u5/boards/stm32u575nucleo/board.h

@@ -0,0 +1,111 @@
+/*
+ * The MIT License (MIT)
+ *
+ * Copyright (c) 2023, Ha Thach (tinyusb.org)
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a copy
+ * of this software and associated documentation files (the "Software"), to deal
+ * in the Software without restriction, including without limitation the rights
+ * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+ * copies of the Software, and to permit persons to whom the Software is
+ * furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in
+ * all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+ * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+ * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+ * THE SOFTWARE.
+ *
+ * This file is part of the TinyUSB stack.
+ */
+
+#ifndef BOARD_H_
+#define BOARD_H_
+
+#ifdef __cplusplus
+extern "C"
+{
+#endif
+
+// LED GREEN
+#define LED_PORT GPIOC
+#define LED_PIN GPIO_PIN_7
+#define LED_STATE_ON 1
+
+// BUTTON
+#define BUTTON_PORT GPIOA
+#define BUTTON_PIN GPIO_PIN_0
+#define BUTTON_STATE_ACTIVE 1
+
+// UART Enable for STLink VCOM
+#define UART_DEV LPUART1
+#define UART_CLK_EN __HAL_RCC_LPUART1_CLK_ENABLE
+#define UART_GPIO_PORT GPIOG
+#define UART_GPIO_AF GPIO_AF8_LPUART1
+#define UART_TX_PIN GPIO_PIN_7
+#define UART_RX_PIN GPIO_PIN_8
+
+//--------------------------------------------------------------------+
+// RCC Clock
+//--------------------------------------------------------------------+
+
+static inline void board_clock_init(void)
+{
+
+  RCC_OscInitTypeDef RCC_OscInitStruct = {0};
+  RCC_ClkInitTypeDef RCC_ClkInitStruct = {0};
+  RCC_PeriphCLKInitTypeDef PeriphClkInit = {0};
+
+  /* Enable Power Clock */
+  __HAL_RCC_PWR_CLK_ENABLE();
+
+  /** Configure the main internal regulator output voltage
+   */
+  HAL_PWREx_ControlVoltageScaling(PWR_REGULATOR_VOLTAGE_SCALE1);
+
+  /** Initializes the CPU, AHB and APB buses clocks
+  */
+  RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI48 | RCC_OSCILLATORTYPE_HSI;
+  RCC_OscInitStruct.HSIState = RCC_HSI_ON;
+  RCC_OscInitStruct.HSI48State = RCC_HSI48_ON;
+  RCC_OscInitStruct.HSICalibrationValue = RCC_HSICALIBRATION_DEFAULT;
+  RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
+  RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI;
+  RCC_OscInitStruct.PLL.PLLMBOOST = RCC_PLLMBOOST_DIV1;
+  RCC_OscInitStruct.PLL.PLLM = 1;
+  RCC_OscInitStruct.PLL.PLLN = 10;
+  RCC_OscInitStruct.PLL.PLLP = 2;
+  RCC_OscInitStruct.PLL.PLLQ = 2;
+  RCC_OscInitStruct.PLL.PLLR = 1;
+  RCC_OscInitStruct.PLL.PLLRGE = RCC_PLLVCIRANGE_1;
+  RCC_OscInitStruct.PLL.PLLFRACN = 0;
+  HAL_RCC_OscConfig(&RCC_OscInitStruct);
+
+  PeriphClkInit.PeriphClockSelection = RCC_PERIPHCLK_CLK48;
+  PeriphClkInit.IclkClockSelection = RCC_CLK48CLKSOURCE_HSI48;
+
+  HAL_RCCEx_PeriphCLKConfig(&PeriphClkInit);
+
+  /** Initializes the CPU, AHB and APB buses clocks
+   */
+  RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2 | RCC_CLOCKTYPE_PCLK3;
+  RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
+  RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
+  RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV1;
+  RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1;
+  RCC_ClkInitStruct.APB3CLKDivider = RCC_HCLK_DIV1;
+
+  HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_4);
+}
+
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* BOARD_H_ */

hw/bsp/stm32u5/boards/stm32u575nucleo/board.mk

@@ -0,0 +1,10 @@
+CFLAGS += \
+  -DSTM32U575xx \
+
+# All source paths should be relative to the top level.
+LD_FILE = ${ST_CMSIS}/Source/Templates/gcc/linker/STM32U575xx_FLASH.ld
+
+SRC_S += $(ST_CMSIS)/Source/Templates/gcc/startup_stm32u575xx.s
+
+# For flash-jlink target
+JLINK_DEVICE = stm32u575zi

hw/bsp/stm32u5/family.c

@@ -69,6 +69,9 @@ void board_init(void) {
 
   UART_CLK_EN();
 
+  /* Enable Instruction cache */
+  HAL_ICACHE_Enable();
+
 #if CFG_TUSB_OS == OPT_OS_NONE
   // 1ms tick timer
   SysTick_Config(SystemCoreClock / 1000);

hw/bsp/stm32u5/family.cmake

@@ -37,6 +37,7 @@ function(add_board_target BOARD_TARGET)
       ${ST_HAL_DRIVER}/Src/${ST_PREFIX}_hal.c
       ${ST_HAL_DRIVER}/Src/${ST_PREFIX}_hal_cortex.c
       ${ST_HAL_DRIVER}/Src/${ST_PREFIX}_hal_gpio.c
+      ${ST_HAL_DRIVER}/Src/${ST_PREFIX}_hal_icache.c
       ${ST_HAL_DRIVER}/Src/${ST_PREFIX}_hal_pwr_ex.c
       ${ST_HAL_DRIVER}/Src/${ST_PREFIX}_hal_rcc.c
       ${ST_HAL_DRIVER}/Src/${ST_PREFIX}_hal_rcc_ex.c

hw/bsp/stm32u5/family.mk

@@ -21,6 +21,7 @@ SRC_C += \
 	$(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal.c \
 	$(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_cortex.c \
 	$(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_gpio.c \
+  $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_icache.c \
 	$(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_pwr.c \
 	$(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_pwr_ex.c \
 	$(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_rcc.c \