Problem on Orange Pi 3B, Debian Bookworm cloning from /dev/mmcblk0 to /dev/mvme0n1

[b-morgan]

I have an Orange Pi 3B with an eMMC (256GB) and an NVMe (256GB) on which I have installed Debian 12 (Bookworm). I have installed rpi-clone 2.0.22 and copied the files to /local/user/sbin as suggested in the README.md.

Here is a lsblk:

NAME         MAJ:MIN RM   SIZE RO TYPE MOUNTPOINTS
mtdblock0     31:0    0    16M  0 disk
mmcblk0      179:0    0   233G  0 disk
├─mmcblk0p1  179:1    0     1G  0 part /boot
└─mmcblk0p2  179:2    0 229.6G  0 part /var/log.hdd
                                       /
mmcblk0boot0 179:32   0     4M  1 disk
mmcblk0boot1 179:64   0     4M  1 disk
zram0        254:0    0   1.9G  0 disk [SWAP]
zram1        254:1    0    50M  0 disk /var/log
nvme0n1      259:0    0 238.5G  0 disk
├─nvme0n1p1  259:1    0     1G  0 part
└─nvme0n1p2  259:4    0 231.9G  0 part

When I attempt to do the clone, I get a Warning that requires a response but I have no idea where it comes from or what response will continue.

root@orangepi3b:~# sys-clone /dev/nvme0n1 -f

  Target disk nvme0n1 ends with a digit so may be a partition.
  sys-clone requires disk names like 'sda' and not partition names like 'sda1'.

Continue anyway?  (yes/no): y
Warning: Not all of the space available to /dev/nvme0n1 appears to be used, you can fix the GPT to use all of the space
(an extra 11563696 blocks) or continue with the current setting?

Here is the output from fdisk for both the source and the target devices:

root@orangepi3b:~# fdisk /dev/mmcblk0

Welcome to fdisk (util-linux 2.38.1).
Changes will remain in memory only, until you decide to write them.
Be careful before using the write command.

This disk is currently in use - repartitioning is probably a bad idea.
It's recommended to umount all file systems, and swapoff all swap
partitions on this disk.


Command (m for help): p

Disk /dev/mmcblk0: 232.96 GiB, 250139901952 bytes, 488554496 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disklabel type: gpt
Disk identifier: C1C93DD0-252E-1A49-8268-4B0FB4B1A113

Device           Start       End   Sectors   Size Type
/dev/mmcblk0p1   61440   2158591   2097152     1G Linux extended boot
/dev/mmcblk0p2 2158592 483655679 481497088 229.6G Linux filesystem

Command (m for help): q

root@orangepi3b:~# fdisk /dev/nvme0n1

Welcome to fdisk (util-linux 2.38.1).
Changes will remain in memory only, until you decide to write them.
Be careful before using the write command.


Command (m for help): p
Disk /dev/nvme0n1: 238.47 GiB, 256060514304 bytes, 500118192 sectors
Disk model: KBG40ZNS256G NVMe KIOXIA 256GB
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disklabel type: gpt
Disk identifier: C1C93DD0-252E-1A49-8268-4B0FB4B1A113

Device           Start       End   Sectors   Size Type
/dev/nvme0n1p1   61440   2158591   2097152     1G Linux extended boot
/dev/nvme0n1p2 2158592 488552447 486393856 231.9G Linux filesystem

Can you tell me what response is needed to continue (and where this warning comes from)?

[b-morgan]

Using bash -x sys-clone /dev/nvme0n1 2>&1 | tee output.log I was able to discover that the message is generated by parted and the valid responses are Fix/Ignore. This allowed the script to continue but there is a new error:

  Mounting /dev/nvme0n12 on /mnt/clone
+ mount /dev/nvme0n12 /mnt/clone
mount: /mnt/clone: special device /dev/nvme0n12 does not exist.
       dmesg(1) may have more information after failed mount system call.
+ echo '    Mount failure of /dev/nvme0n12 on /mnt/clone.'
    Mount failure of /dev/nvme0n12 on /mnt/clone.
+ '[' '' '!=' '' ']'
+ echo 'Aborting!'
Aborting!
+ exit 1

From the previous fdisk output the partitions are nvme0n1p1 and nvme0n1p2.

[framps]

You should check #147 because rpi-clone does not support NVMe

[b-morgan]

@framps Thanks! That issue gave me the clue but there were two lines that needed to be changed, 576:

	if [[ $disk == *"mmcblk"* || $disk == *"nvme"* ]]

and 1062:

	if [[ $dst_disk == *"mmcblk"* || $disk == *"nvme"* ]]

[STR4NG3RdotSH]

@framps Thanks! That issue gave me the clue but there were two lines that needed to be changed, 576:

	if [[ $disk == *"mmcblk"* || $disk == *"nvme"* ]]

and 1062:

	if [[ $dst_disk == *"mmcblk"* || $disk == *"nvme"* ]]

Great tweak, @b-morgan
This got my attempt to clone SD -> NVMe past the issue I was having, after fixing your typo.
Line 1062 should actually read:
if [[ $dst_disk == *"mmcblk"* || $dst_disk == *"nvme"* ]]
Just a heads up for anyone else who arrives here and doesn't notice it.
Cloning process completed and reported success. Despite that, the clone system boots to initramfs command line for BusyBox. Currently troubleshooting that...

[STR4NG3RdotSH]

Disregard my responses. The best option is to use Jeff's (@geerlingguy) version/fork:
https://rpi-clone.jeffgeerling.com

After troubleshooting above for a short time I full removed and reinstalled his fork, ran clone to my nvme with no flags or script edits. Immediate success and system booted great.

[framps]

Yes, everybody should head over to Jeff's repo. Bills repo is no longer maintained and rpi-clone does not work on Bookworm any more.