diff --git a/configs/SPRACINGH7EVO/config.h b/configs/SPRACINGH7EVO/config.h new file mode 100644 index 00000000..5eb36ea3 --- /dev/null +++ b/configs/SPRACINGH7EVO/config.h @@ -0,0 +1,283 @@ +/* + * This file is part of Betaflight. + * + * Betaflight is free software. You can redistribute this software + * and/or modify this software under the terms of the GNU General + * Public License as published by the Free Software Foundation, + * either version 3 of the License, or (at your option) any later + * version. + * + * Betaflight is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. + * + * See the GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public + * License along with this software. + * + * If not, see . + */ + +#define FC_TARGET_MCU STM32H730 + +#define BOARD_NAME SPRACINGH7EVO +#define MANUFACTURER_ID SPRO + +#define TARGET_BOARD_IDENTIFIER "SP7V" +#define USBD_PRODUCT_STRING "SPRacingH7EVO" + +#define FC_VMA_ADDRESS 0x90100000 + +#define EEPROM_SIZE 8192 + +#define USE_SPRACING_PERSISTENT_RTC_WORKAROUND + +// No physical buttons, BIND pad on bottom can be connected though a 10k resistor and switch to V3P3+ +#define USE_BUTTONS +#define BUTTON_A_PIN PC14 +#define BUTTON_A_PIN_INVERTED +#define BUTTON_B_PIN PC14 +#define BUTTON_B_PIN_INVERTED + +// Device has 2x flash chips in parallel using a single CS pin, initial support is for the first flash chip only. +#define USE_OCTOSPI +#define USE_OCTOSPI_DEVICE_1 + +#define USE_SPI + +// On mezzanine expansion connector, for external flash for logging, second gyro, sx1280, etc +#define USE_SPI_DEVICE_1 +#define SPI1_SCK_PIN PA5 +#define SPI1_SDI_PIN PB4 +#define SPI1_SDO_PIN PB5 +#define SPI1_NSS_PIN PA15 + +#define USE_SPI_DEVICE_2 +#define SPI2_SCK_PIN PD3 +#define SPI2_SDI_PIN PB14 +#define SPI2_SDO_PIN PB15 +#define SPI2_NSS_PIN PB12 + +// SX1280 not installed, signals on mezzanine connector +#define SX1280_BUSY_PIN PC7 +#define SX1280_DIO1_PIN PD4 +#define SX1280_DIO2_PIN NONE +#define SX1280_DIO3_PIN NONE + +#define USE_FLASH_MEMORY_MAPPED +#define FLASH_OCTOSPI_INSTANCE OCTOSPI1 +#define CONFIG_IN_MEMORY_MAPPED_FLASH +#define USE_FIRMWARE_PARTITION + +#define USE_SDCARD_SDIO +#define SDCARD_DETECT_PIN PC13 +#define SDCARD_DETECT_INVERTED +#define SDIO_DEVICE SDIODEV_1 +#define SDIO_USE_4BIT 1 +#define SDIO_CK_PIN PC12 +#define SDIO_CMD_PIN PD2 +#define SDIO_D0_PIN PC8 +#define SDIO_D1_PIN PC9 +#define SDIO_D2_PIN PC10 +#define SDIO_D3_PIN PC11 + +// OCTOSPI pins excluded, as bootloader runs firmware in memory mapped mode +#define TARGET_IO_PORTA 0xffff +#define TARGET_IO_PORTB (0xffff & ~(BIT(2)|BIT(6))) +#define TARGET_IO_PORTC 0xffff +#define TARGET_IO_PORTD (0xffff & ~(BIT(11)|BIT(12)|BIT(13))) +#define TARGET_IO_PORTE (0xffff & ~(BIT(2)|BIT(7)|BIT(8)|BIT(9)|BIT(10))) +#define TARGET_IO_PORTF 0xffff +#define TARGET_IO_PORTG 0xffff +#define TARGET_IO_PORTH 0xffff + +#define USE_I2C + +#define I2C1_SCL_PIN NONE +#define I2C1_SDA_PIN NONE + +// on GPS connector and mezzanine expansion connector +// 10k pull-ups installed +#define USE_I2C_DEVICE_2 +#define I2C2_SCL_PIN PB10 +#define I2C2_SDA_PIN PB11 + +#define I2C3_SCL_PIN NONE +#define I2C3_SDA_PIN NONE + +#define I2C4_SCL_PIN NONE +#define I2C4_SDA_PIN NONE + + +#define MAG_I2C_INSTANCE (I2CDEV_2) +#define BARO_I2C_INSTANCE (I2CDEV_2) + +#define USE_MPU_DATA_READY_SIGNAL +#define ENSURE_MPU_DATA_READY_IS_LOW + + +#define DEFAULT_RX_FEATURE FEATURE_RX_SERIAL +#define DEFAULT_FEATURES (FEATURE_TELEMETRY | FEATURE_LED_STRIP) + +#define ADC3_DMA_OPT 10 +#define ADC_INSTANCE ADC3 +#define ADC1_INSTANCE ADC1 +#define ADC3_INSTANCE ADC3 + +// Hardware ADC pins and intended usage +#define CURRENT_METER_1_ADC_PIN PC3 +#define CURRENT_METER_1_ADC_INSTANCE ADC3 +#define CURRENT_METER_2_ADC_PIN PC1 +#define CURRENT_METER_2_ADC_INSTANCE ADC3 +#define ADC_EXTERNAL1_PIN PC2 +#define ADC_EXTERNAL1_INSTANCE ADC3 +#define VBAT_ADC_INSTANCE ADC3 +// Video IN/Out ADC pins are N/C, reserved in schematic +#define VIDEO_IN_ADC_PIN PC5 +#define VIDEO_OUT_ADC_PIN PC4 + +// BF usage of ADC pins +#define ADC_VBAT_PIN PC0 +#define ADC_RSSI_PIN PC1 // current meter 2 on 4in1ESC2 connector +#define ADC_CURR_PIN PC3 // current meter 1 on 4in1ESC2 connector +#define ADC_EXTERNAL1_PIN PC2 // on mezannine connector + +#define VTX_ENABLE_PIN PC15 +#define PINIO1_PIN VTX_ENABLE_PIN + +#define USE_ACC +#define USE_ACC_SPI_ICM42605 +#define USE_ACC_SPI_ICM42688P +#define USE_GYRO +#define USE_GYRO_SPI_ICM42605 +#define USE_GYRO_SPI_ICM42688P +#define USE_BARO +#define USE_BARO_BMP388 +#define USE_MAG +#define USE_MAG_HMC5883 +#define USE_MAG_QMC5883 +#define USE_FLASH_W25Q128FV +#define USE_SDCARD +// The target has a specific set of pads for the LED strip. +#ifndef USE_LED_STRIP +#define USE_LED_STRIP +#endif + +// Pin layout supports SPRacingPixelOSD and signals reserved in schematic. +#define VIDEO_IN_ADC_PIN PC5 +#define VIDEO_OUT_ADC_PIN PC4 +#define SPRACING_PIXEL_OSD_BLACK_PIN PE12 +#define SPRACING_PIXEL_OSD_WHITE_PIN PE13 +#define SPRACING_PIXEL_OSD_MASK_ENABLE_PIN PE14 +#define SPRACING_PIXEL_OSD_WHITE_SOURCE_SELECT_PIN PE15 + +#define SPRACING_PIXEL_OSD_SYNC_IN_PIN PE11 +#define SPRACING_PIXEL_OSD_SYNC_OUT_PIN PA8 + +#define SPRACING_PIXEL_OSD_WHITE_SOURCE_PIN PA4 +#define SPRACING_PIXEL_OSD_VIDEO_THRESHOLD_DEBUG_PIN PA5 // used by SPI1_CLK on mezzanine connector + +#define SPRACING_PIXEL_OSD_PIXEL_DEBUG_1_PIN PE5 // led 0 +#define SPRACING_PIXEL_OSD_PIXEL_DEBUG_2_PIN PE6 // led 1 +#define SPRACING_PIXEL_OSD_PIXEL_GATING_DEBUG_PIN PB0 // pwm 6 +#define SPRACING_PIXEL_OSD_PIXEL_BLANKING_DEBUG_PIN PB1 // pwm 5 + +#define BEEPER_INVERTED +#define BEEPER_PIN PE4 + +// RX and TX on "RX" connector, RX on "HD-VTX" connector +#define UART1_TX_PIN PA9 +#define UART1_RX_PIN PA10 + +// on mezzanine connector +#define UART2_TX_PIN PD5 +#define UART2_RX_PIN PD6 + +// RX and TX on "HD-VTX" connector +#define UART3_TX_PIN PD8 +#define UART3_RX_PIN PD9 + +// for ESC TLM, with series 10k resistor +#define UART5_TX_PIN NONE +#define UART5_RX_PIN PB13 // TX signal pin-swapped + +// on mezzanine connector (other useful signals on these pins too) +#define UART4_TX_PIN PB9 +#define UART4_RX_PIN PB8 + +#define UART6_TX_PIN NONE +#define UART6_RX_PIN NONE + +#define UART7_TX_PIN NONE +#define UART7_RX_PIN NONE + +// on GPS connector +#define UART8_TX_PIN PE1 +#define UART8_RX_PIN PE0 + +#define UART9_TX_PIN NONE +#define UART9_RX_PIN NONE + +#define UART10_TX_PIN NONE +#define UART10_RX_PIN NONE + +// 8Mbps CAN transceiver installed with CAN termination, CANL/CANH available on GPS, mezzanine and servo connectors. +#define FDCAN1_RX PD0 +#define FDCAN2_RX PD1 + +#define LED0_PIN PE5 +#define LED1_PIN PE6 +#define LED2_PIN NONE + +#define SPEKTRUM_RX_BIND_PIN NONE +#define RX_BIND_PLUG_PIN NONE + +#define RX_SPI_CS_PIN PA15 +//#define RX_SPI_EXTI_PIN PD4 +#define RX_SPI_BIND_PIN NONE +#define RX_SPI_LED_PIN NONE +#define RX_SPI_EXPRESSLRS_RESET_PIN PD10 +#define RX_SPI_EXPRESSLRS_BUSY_PIN PC7 + +#define GYRO_1_EXTI_PIN PE3 +#define GYRO_2_EXTI_PIN PC15 // on mezzanine connector +#define GYRO_1_CS_PIN PB12 +#define GYRO_2_CS_PIN PA15 // on mezzanine connector + +#define MOTOR1_PIN PA3 +#define MOTOR2_PIN PA2 +#define MOTOR3_PIN PA1 +#define MOTOR4_PIN PA0 +#define MOTOR5_PIN PB1 +#define MOTOR6_PIN PB0 +#define MOTOR7_PIN PA7 +#define MOTOR8_PIN PA6 +#define LED_STRIP_PIN PC6 + +// Index, Pin, 1-based occurrence of pin in fullTimerHardware, dma opt (use -1 for no DMA) +// See timerio.c and timer_stm32h7xx.c + +#define TIMER_PIN_MAPPING \ + TIMER_PIN_MAP( 0, PA3 , 2, 7 ) \ + TIMER_PIN_MAP( 1, PA2 , 2, 6 ) \ + TIMER_PIN_MAP( 2, PA1 , 2, 5 ) \ + TIMER_PIN_MAP( 3, PA0 , 2, 4 ) \ + TIMER_PIN_MAP( 4, PB1 , 2, 1 ) \ + TIMER_PIN_MAP( 5, PB0 , 2, 0 ) \ + TIMER_PIN_MAP( 6, PA7 , 2, 3 ) \ + TIMER_PIN_MAP( 7, PA6 , 1, 2 ) \ + TIMER_PIN_MAP( 8, PC6 , 2, 8 ) + +#define DEFAULT_BLACKBOX_DEVICE BLACKBOX_DEVICE_SDCARD + +#define DEFAULT_CURRENT_METER_SOURCE CURRENT_METER_ADC +#define DEFAULT_VOLTAGE_METER_SOURCE VOLTAGE_METER_ADC + +#define GYRO_1_SPI_INSTANCE SPI2 +#define GYRO_1_ALIGN CW270_DEG_FLIP + +// Prevent flash being used for logs as target requires EXST +#ifdef USE_FLASH +#undef USE_FLASH +#endif diff --git a/configs/SPRACINGH7EXTREME/config.h b/configs/SPRACINGH7EXTREME/config.h index e124cae5..b4ec3fcc 100644 --- a/configs/SPRACINGH7EXTREME/config.h +++ b/configs/SPRACINGH7EXTREME/config.h @@ -240,7 +240,6 @@ #define DEFAULT_BLACKBOX_DEVICE BLACKBOX_DEVICE_FLASH #define DEFAULT_GYRO_TO_USE GYRO_CONFIG_USE_GYRO_BOTH -#define USE_SPI_GYRO #define GYRO_1_SPI_INSTANCE SPI3 #define GYRO_1_ALIGN CW180_DEG #define GYRO_2_SPI_INSTANCE SPI2 diff --git a/configs/SPRACINGH7NANO/config.h b/configs/SPRACINGH7NANO/config.h index 45db478c..f0554cc0 100644 --- a/configs/SPRACINGH7NANO/config.h +++ b/configs/SPRACINGH7NANO/config.h @@ -230,7 +230,6 @@ #define BARO_I2C_INSTANCE (I2CDEV_1) #define DEFAULT_GYRO_TO_USE GYRO_CONFIG_USE_GYRO_1 -#define USE_SPI_GYRO #define GYRO_1_SPI_INSTANCE SPI2 #define GYRO_1_ALIGN CW0_DEG_FLIP #define GYRO_2_SPI_INSTANCE SPI3 diff --git a/configs/SPRACINGH7RF/config.h b/configs/SPRACINGH7RF/config.h index 64f5424f..5c74af19 100644 --- a/configs/SPRACINGH7RF/config.h +++ b/configs/SPRACINGH7RF/config.h @@ -297,7 +297,6 @@ #define DEFAULT_CURRENT_METER_SOURCE CURRENT_METER_ADC #define DEFAULT_VOLTAGE_METER_SOURCE VOLTAGE_METER_ADC -#define USE_SPI_GYRO #define GYRO_1_SPI_INSTANCE SPI6 #define GYRO_1_ALIGN CW270_DEG_FLIP diff --git a/configs/SPRACINGH7ZERO/config.h b/configs/SPRACINGH7ZERO/config.h index ef2846c1..03b98f59 100644 --- a/configs/SPRACINGH7ZERO/config.h +++ b/configs/SPRACINGH7ZERO/config.h @@ -231,7 +231,6 @@ #define BARO_I2C_INSTANCE (I2CDEV_1) #define DEFAULT_GYRO_TO_USE GYRO_CONFIG_USE_GYRO_1 -#define USE_SPI_GYRO #define GYRO_1_SPI_INSTANCE SPI3 #define GYRO_1_ALIGN CW180_DEG #define GYRO_2_SPI_INSTANCE SPI2