Edit yaml file with website

[FMD14]

Wiki Search Terms

Edit yaml file with website

Controller Board

DLC MKS 32 V2.1

Machine Description

Laser corexy Neje 30w

Input Circuits

No response

Configuration file

board: MKS-DLC32 V2.1
name: CoreXY Laser NJE 30W
meta: 02/11/2022 FMD14

kinematics:
  corexy:

stepping:
  engine: I2S_STATIC
  idle_ms: 0
  pulse_us: 4
  dir_delay_us: 1
  disable_delay_us: 0

axes:
  shared_stepper_disable_pin: I2SO.0
  x:
    steps_per_mm: 80
    max_rate_mm_per_min: 25000.000
    acceleration_mm_per_sec2: 3200.000
    max_travel_mm: 515.00
    soft_limits: false
    homing:
      cycle: 1
      positive_direction: false
      mpos_mm: 0.000
      feed_mm_per_min: 300.000
      seek_mm_per_min: 7000.000
      settle_ms: 525.00
      seek_scaler: 1.100
      feed_scaler: 1.100

    motor0:
      limit_neg_pin: gpio.35:low
      hard_limits: true
      pulloff_mm: 2.000
      stepstick:
        step_pin: I2SO.1
        direction_pin: I2SO.2:low

  y:
    steps_per_mm: 80
    max_rate_mm_per_min: 25000.000
    acceleration_mm_per_sec2: 3200.000
    max_travel_mm: 555.00
    soft_limits: false
    homing:
      cycle: 2
      positive_direction: false
      mpos_mm: 0.000
      feed_mm_per_min: 300.000
      seek_mm_per_min: 7000.000
      settle_ms: 500
      seek_scaler: 1.100
      feed_scaler: 1.100

    motor0:
      limit_neg_pin: gpio.36:low
      hard_limits: true
      pulloff_mm: 2.000
      stepstick:
        step_pin: I2SO.5
        direction_pin: I2SO.6:low

  z:
    steps_per_mm: 157.750
    max_rate_mm_per_min: 1200.000
    acceleration_mm_per_sec2: 500.000
    max_travel_mm: 80.000
    soft_limits: true
    homing:
      cycle: 0
      positive_direction: false
      mpos_mm: 0.000
      feed_mm_per_min: 300.000
      seek_mm_per_min: 1000.000
      settle_ms: 500
      seek_scaler: 1.100
      feed_scaler: 1.100

    motor0:
      limit_neg_pin: gpio.34:low
      hard_limits: false
      pulloff_mm: 1.000
      stepstick:
        step_pin: I2SO.3
        direction_pin: I2SO.4:low

i2so:
  bck_pin: gpio.16
  data_pin: gpio.21
  ws_pin: gpio.17

spi:
  miso_pin: gpio.12
  mosi_pin: gpio.13
  sck_pin: gpio.14

sdcard:
  cs_pin: gpio.15
  card_detect_pin: NO_PIN

control:
  safety_door_pin: NO_PIN
  reset_pin: NO_PIN
  feed_hold_pin: NO_PIN
  cycle_start_pin: NO_PIN
  macro0_pin: gpio.33:low:pu
  macro1_pin: NO_PIN
  macro2_pin: NO_PIN
  macro3_pin: NO_PIN

macros:
  startup_line0: 
  startup_line1: 
  macro0: $SD/Run=lasertest.gcode
  macro1: $SD/Run=home.gcode
  macro2:
  macro3:

coolant:
  flood_pin: NO_PIN
  mist_pin: NO_PIN
  delay_ms: 0

probe:
  pin: gpio.22
  check_mode_start: true

Laser:
  pwm_hz: 5000
  #L on Beeper / IN on TTL
  output_pin: gpio.32
  enable_pin: I2SO.7
  disable_with_s0: false
  s0_with_disable: false
  tool_num: 0
  speed_map: 0=0.000%  1000=100.000%
# 135=0mA 270=5mA 400=10mA 700=16mA

user_outputs:
  analog0_pin: NO_PIN
  analog1_pin: NO_PIN
  analog2_pin: NO_PIN
  analog3_pin: NO_PIN
  analog0_hz: 5000
  analog1_hz: 5000
  analog2_hz: 5000
  analog3_hz: 5000
  digital0_pin: NO_PIN
  digital1_pin: NO_PIN
  digital2_pin: NO_PIN
  digital3_pin: NO_PIN

start:
  must_home: false

# 5,18,19,22,23,25,26,27,32,33,39,I2SO.7
# SDA 0 / SCL 4

Startup Messages

Pas de message

User Interface Software

LaserGRBL LightBurn

What happened?

How to do the yaml file with the web interface
the old version we had access to the yaml file. Now when I click on the file it will download it
I would like to change the movement speed

GCode File

No response

Other Information

[breiler]

The config file editor is available at https://installer.fluidnc.com

[FMD14]

I connect with the IP address
However, I don't see the yaml file.
my laser moves when I homing
how to install install editor
I don't speak English

[FMD14]

Good evening
I succeeded thanks to you The version has changed a lot
It's more user-friendly
Thanks again

[FMD14]

hello, I modified values ​​in the yaml file with fluidnc web installer. I saved I did a restart. When I launched it asked me to create a config file. My question can we modify the file live. I reinstalled the version and the yaml file