Flow Test Generator Settings SV06.

[bassamanator]

If you're interested in doing a flow test, you can use the following settings for this site: https://hotend-flow-tester.netlify.app/. Just throw the relevant JSON into your browsers Local Storage. Note, I've found that this method works best in Firefox. Be ready to hit power off in case there is a collision!

Firefox:

Print:

If you use Klipper:

{
	"state": {
		"options": {
			"bedWidth": 223,
			"bedLength": 223,
			"bedMargin": 2,
			"safeZPark": 10,
			"filamentDiameter": 1.75,
			"travelSpeed": 100,
			"dwellTime": 10,
			"bedTemp": 60,
			"fanSpeed": 70,
			"primeLength": 25,
			"primeAmount": 20,
			"primeSpeed": 5,
			"wipeLength": 15,
			"retractionDistance": 0.5,
			"retractionSpeed": 40,
			"blobHeight": 15,
			"extrusionAmount": 200,
			"direction": 1,
			"flowSpacing": 70,
			"tempSpacing": 45,
			"flowStart": 10,
			"flowOffset": 1,
			"flowSteps": 9,
			"flowEnd": 18,
			"tempStart": 240,
			"tempOffset": 0,
			"tempSteps": 1,
			"tempEnd": 240,
			"startGcode": "M106 S178 ; Set Fan Speed\nM104 S0 ; Stops PS/SS from sending temp waits separately\nM140 S0\nM117\nPRINT_START BED=50 HOTEND=240",
			"endGcode": "PRINT_END"
		},
		"fileName": "240-10-18",
		"showVariableNames": true,
		"startGcodeError": "",
		"endGcodeError": ""
	},
	"version": "0.4.6"
}

Minified:

{"state":{"options":{"bedWidth":223,"bedLength":223,"bedMargin":2,"safeZPark":10,"filamentDiameter":1.75,"travelSpeed":100,"dwellTime":10,"bedTemp":60,"fanSpeed":70,"primeLength":25,"primeAmount":20,"primeSpeed":5,"wipeLength":15,"retractionDistance":0.5,"retractionSpeed":40,"blobHeight":15,"extrusionAmount":200,"direction":1,"flowSpacing":70,"tempSpacing":45,"flowStart":10,"flowOffset":1,"flowSteps":9,"flowEnd":18,"tempStart":240,"tempOffset":0,"tempSteps":1,"tempEnd":240,"startGcode":"M106 S178 ; Set Fan Speed\nM104 S0 ; Stops PS/SS from sending temp waits separately\nM140 S0\nM117\nPRINT_START BED=50 HOTEND=240","endGcode":"PRINT_END"},"fileName":"test-3-col","showVariableNames":true,"startGcodeError":"","endGcodeError":""},"version":"0.4.6"}

Marlin (UNTESTED)

{
	"state": {
		"options": {
			"bedWidth": 223,
			"bedLength": 223,
			"bedMargin": 2,
			"safeZPark": 10,
			"filamentDiameter": 1.75,
			"travelSpeed": 100,
			"dwellTime": 10,
			"bedTemp": 60,
			"fanSpeed": 70,
			"primeLength": 25,
			"primeAmount": 20,
			"primeSpeed": 5,
			"wipeLength": 15,
			"retractionDistance": 0.5,
			"retractionSpeed": 40,
			"blobHeight": 15,
			"extrusionAmount": 200,
			"direction": 1,
			"flowSpacing": 70,
			"tempSpacing": 45,
			"flowStart": 10,
			"flowOffset": 1,
			"flowSteps": 9,
			"flowEnd": 18,
			"tempStart": 240,
			"tempOffset": 0,
			"tempSteps": 1,
			"tempEnd": 240,
			"startGcode": "M104 S${tempStart} ; Set Nozzle Temperature\nM140 S${bedTemp} ; Set Bed Temperature\nG90 ; Absolute positioning\nG28 ; Move to home position\nG0 Z${safeZPark} ; Lift nozzle\nG21 ; unit in mm\nG92 E0 ; reset extruder\nM83 ; set extruder to relative mode\nM190 S${bedTemp} ; Wait for Bed Temperature\nM106 S${fanSpeed} ; Set Fan Speed\n; M203 I0.1 ; Uncomment for Duet/RRF (slow z-moves)\n; PRINT_START\n; PRINT_START EXTRUDER=${tempStart} BED=${bedTemp}\n",
			"endGcode": "G4 ; Wait for buffer to clear\nG0 X${bedWidth - bedMargin} \nY${bedLength - bedMargin} ; Move to Corner\nM104 S0 T0 ; Turn Off Hotend\nM140 S0 ; Turn Off Bed\nM84 ; Disable Steppers\n; PRINT_END"
		},
		"fileName": "240-10-18",
		"showVariableNames": true,
		"startGcodeError": "",
		"endGcodeError": ""
	},
	"version": "0.4.6"
}

Minified

{"state":{"options":{"bedWidth":223,"bedLength":223,"bedMargin":2,"safeZPark":10,"filamentDiameter":1.75,"travelSpeed":100,"dwellTime":10,"bedTemp":60,"fanSpeed":70,"primeLength":25,"primeAmount":20,"primeSpeed":5,"wipeLength":15,"retractionDistance":0.5,"retractionSpeed":40,"blobHeight":15,"extrusionAmount":200,"direction":1,"flowSpacing":70,"tempSpacing":45,"flowStart":10,"flowOffset":1,"flowSteps":9,"flowEnd":18,"tempStart":240,"tempOffset":0,"tempSteps":1,"tempEnd":240,"startGcode":"M104 S${tempStart} ; Set Nozzle Temperature\nM140 S${bedTemp} ; Set Bed Temperature\nG90 ; Absolute positioning\nG28 ; Move to home position\nG0 Z${safeZPark} ; Lift nozzle\nG21 ; unit in mm\nG92 E0 ; reset extruder\nM83 ; set extruder to relative mode\nM190 S${bedTemp} ; Wait for Bed Temperature\nM106 S${fanSpeed} ; Set Fan Speed\n; M203 I0.1 ; Uncomment for Duet/RRF (slow z-moves)\n; PRINT_START\n; PRINT_START EXTRUDER=${tempStart} BED=${bedTemp}\n","endGcode":"G4 ; Wait for buffer to clear\nG0 X${bedWidth - bedMargin} \nY${bedLength - bedMargin} ; Move to Corner\nM104 S0 T0 ; Turn Off Hotend\nM140 S0 ; Turn Off Bed\nM84 ; Disable Steppers\n; PRINT_END"},"fileName":"240-10-18","showVariableNames":true,"startGcodeError":"","endGcodeError":""},"version":"0.4.6"}