diff --git a/source/linux/How_to_Guides/Target/How_to_enable_Microtips_LVDS_Panel.rst b/source/linux/How_to_Guides/Target/How_to_enable_Microtips_LVDS_Panel.rst
index 022757b93..954ca10db 100644
--- a/source/linux/How_to_Guides/Target/How_to_enable_Microtips_LVDS_Panel.rst
+++ b/source/linux/How_to_Guides/Target/How_to_enable_Microtips_LVDS_Panel.rst
@@ -7,8 +7,11 @@ is supported on platforms:
    - `AM62X SK <https://www.ti.com/tool/SK-AM62>`__
    - `AM62X LP SK <https://www.ti.com/tool/SK-AM62-LP>`__
    - `AM62P SK <https://www.ti.com/tool/SK-AM62P-LP>`__
+   - `AM62B SK <https://www.ti.com/tool/SK-AM62B>`__
+   - `AM62B-P1 <https://www.ti.com/tool/SK-AM62B-P1>`__
 
-**Steps to enable OLDI Panel DT overlay:**
+Steps to enable OLDI Panel DT overlay
+-------------------------------------
 
 #. Follow the :ref:`How to enable DT overlays in linux <howto_dt_overlays>` guide for steps on building
    and adding the overlay to your SD card. Make sure the correct overlay file has been appended
@@ -33,25 +36,50 @@ is supported on platforms:
       +---------------+---------------------------------------------+
 
 
-**Steps to enable Touch on the Microtips Panel on AM625 SK EVM:**
+Steps to enable Touch on the Microtips Panel on AM625 SK EVM
+------------------------------------------------------------
 
-**Note**: The following steps are only applicable on AM625 SK EVM revision E3 board
+AM62X SK E3 revision
+^^^^^^^^^^^^^^^^^^^^
 
 #. Power off the LVDS board by disconnecting the 12V barrel jack (do not power off the SK EVM)
 #. Run the following commands from the Linux prompt:
 
-	.. code-block:: bash
+   .. code-block:: console
 
-		root@am62xx-evm:~# modprobe -r ili210x
-		root@am62xx-evm:~# i2ctransfer -f -y 0 w3@0x3f 0x09 0x1 0x0e
-		root@am62xx-evm:~# i2ctransfer -f -y 0 w6@0x3f 0x08 0x04 0x47 0x50 0x73 0x68
-		root@am62xx-evm:~# i2ctransfer -f -y 0 w1@0x3f 0x72 r9
+      root@am62xx-evm:~# modprobe -r ili210x
+      root@am62xx-evm:~# i2ctransfer -f -y 0 w3@0x3f 0x09 0x1 0x0e
+      root@am62xx-evm:~# i2ctransfer -f -y 0 w6@0x3f 0x08 0x04 0x47 0x50 0x73 0x68
+      root@am62xx-evm:~# i2ctransfer -f -y 0 w1@0x3f 0x72 r9
 
 #. Power on the LVDS board
 #. Run the following command:
 
-	.. code-block:: bash
+   .. code-block:: console
 
-		root@am62xx-evm:~# modprobe ili210x
+      root@am62xx-evm:~# modprobe ili210x
 
 After re-initializing the module, the touch IC should now be registered as an input and touch should be functional.
+
+AM62B SK & AM62B-P1
+^^^^^^^^^^^^^^^^^^^
+
+#. Run the following command
+
+   .. code-block:: console
+
+      root@am62xx-evm:~# modprobe -r ili210x
+
+#. Power off the LVDS panel by disconnecting the 12V barrel jack (do not power off the SK EVM)
+#. Power on the LVDS panel
+#. Run the following command
+
+   .. code-block:: console
+
+      root@am62xx-evm:~# modprobe ili210x
+
+After re-initializing the module, the touch IC should now be registered as an input and touch should be functional.
+
+.. note::
+
+   ``i2ctransfer`` not required for AM62B SK & AM62B-P1