pytest.ini

[pytest]
# only the files with prefix `pytest_` would be recognized as pytest test scripts.
python_files = pytest_*.py

# ignore PytestExperimentalApiWarning for record_xml_attribute
# set traceback to "short" to prevent the overwhelming tracebacks
addopts =
  -s
  --embedded-services esp,idf
  --tb short
  --strict-markers
  --skip-check-coredump y
  --logfile-extension ".txt"

# ignore DeprecationWarning
filterwarnings =
  ignore::DeprecationWarning:matplotlib.*:
  ignore::DeprecationWarning:google.protobuf.*:
  ignore::_pytest.warning_types.PytestExperimentalApiWarning

markers =
  # target markers
  esp32: support esp32 target
  esp32s2: support esp32s2 target
  esp32s3: support esp32s3 target
  esp32c3: support esp32c3 target
  esp32c2: support esp32c2 target
  esp32c6: support esp32c6 target
  esp32h4: support esp32h4 target
  supported_targets: support all supported targets ('esp32', 'esp32s2', 'esp32c3', 'esp32s3', 'esp32c2', 'esp32c6')
  preview_targets: support all preview targets ('linux', 'esp32h4')
  all_targets: support all targets, including supported ones and preview ones
  temp_skip_ci: temp skip ci for specified targets, can only work with `supported_targets`, `preview_targets`, `all_targets`

  # env markers
  generic: tests should be run on generic runners
  nightly_run: tests should be executed as part of the nightly trigger pipeline
  flash_suspend: support flash suspend feature
  ip101: connected via wired 10/100M ethernet
  lan8720: connected via LAN8720 ethernet transceiver
  quad_psram: runners with quad psram
  octal_psram: runners with octal psram
  usb_host: usb host runners
  usb_host_flash_disk: usb host runners with USB flash disk attached
  usb_device: usb device runners
  ethernet_ota: ethernet OTA runners
  flash_encryption: Flash Encryption runners
  flash_encryption_f4r8: Flash Encryption runners with 4-line flash and 8-line psram
  flash_encryption_f8r8: Flash Encryption runners with 8-line flash and 8-line psram
  flash_mutli: Multiple flash chips tests
  psram: Chip has 4-line psram
  ir_transceiver: runners with a pair of IR transmitter and receiver
  twai_transceiver: runners with a TWAI PHY transceiver
  flash_encryption_wifi_high_traffic: Flash Encryption runners with wifi high traffic support
  ethernet: ethernet runner
  ethernet_flash_8m: ethernet runner with 8mb flash
  ethernet_router: both the runner and dut connect to the same router through ethernet NIC
  wifi_ap: a wifi AP in the environment
  wifi_router: both the runner and dut connect to the same wifi router
  wifi_high_traffic: wifi high traffic runners
  wifi_wlan: wifi runner with a wireless NIC
  xtal_26mhz: runner with 26MHz xtal on board
  xtal_40mhz: runner with 40MHz xtal on board
  external_flash: external flash memory connected via VSPI (FSPI)
  sdcard_sdmode: sdcard running in SD mode
  sdcard_spimode: sdcard running in SPI mode
  MSPI_F8R8: runner with Octal Flash and Octal PSRAM
  MSPI_F4R8: runner with Quad Flash and Octal PSRAM
  MSPI_F4R4: runner with Quad Flash and Quad PSRAM
  test_jtag_arm: runner where the chip is accessible through JTAG as well
  adc: ADC related tests should run on adc runners
  xtal32k: Runner with external 32k crystal connected
  no32kXtal: Runner with no external 32k crystal connected
  multi_dut_modbus_rs485: a pair of runners connected by RS485 bus
  psramv0: Runner with PSRAM version 0

  # multi-dut markers
  ieee802154: ieee802154 related tests should run on ieee802154 runners.
  i154_multi_dut: tests should be used for i154, such as openthread.
  wifi_two_dut: tests should be run on runners which has two wifi duts connected.
  generic_multi_device: generic multiple devices whose corresponding gpio pins are connected to each other.
  twai_network: multiple runners form a TWAI network.
  sdio_master_slave: Test sdio multi board.

  # host_test markers
  host_test: tests which shouldn not be built at the build stage, and instead built in host_test stage.
  qemu: build and test using qemu-system-xtensa, not real target.

# log related
log_cli = True
log_cli_level = INFO
log_cli_format = %(asctime)s %(levelname)s %(message)s
log_cli_date_format = %Y-%m-%d %H:%M:%S

# junit related
junit_family = xunit1

## log all to `system-out` when case fail
junit_logging = stdout
junit_log_passing_tests = False