statescanner.xml

<?xml version="1.0" encoding="UTF-8"?>
<statescanner>
	<scan id="20000">
		<type>Warning</type>
		<message>The Device did not acknowledge the message of type
			"${topic}". You should investigate if this device really supports the
			associated CommandClass
		</message>
		<moreinfo>DeviceConfigError</moreinfo>
		<module>DroppedMsg</module>
	</scan>
	<scan id="20001">
		<regex>Enable SUC</regex>
		<type>Error</type>
		<message>Your Controller does not support SUC mode. You should set
			EnableSIS to false in Options.xml
		</message>
		<moreinfo>ControllerErrors</moreinfo>
		<module>DroppedMsg</module>
	</scan>
	<scan id="20002">
		<regex>SecurityCmd_SchemeGet</regex>
		<type>Error</type>
		<message>Your Secure Device did not respond during Inclusion to the
			Security Setup Messages. You should check how long it took between
			including the device and receiving this message (There maybe
			additional Warnings/Errors related to this message)
		</message>
		<moreinfo>SecurityInclusion</moreinfo>
		<module>DroppedMsg</module>
	</scan>
	<scan id="20003">
		<type>Warning</type>
		<message>The Time it took the Controller to discover the Node and
			Start the Secure inclusion was ${time} seconds. Secure Inclusion
			Might fail for anything over 15 seconds based on experience. You may
			need to retry a few times to see if the process will complete quicker
		</message>
		<moreinfo>SecurityInclusion</moreinfo>
		<module>Security</module>
	</scan>
	<scan id="20004">
		<regex>SecurityCmd_SchemeGet</regex>
		<type>Error</type>
		<message>The Time it took the Controller to discover the Node and
			Start the Secure inclusion was ${time} seconds. Secure Inclusion has
			probably failed (anything over 15 seconds will most likely fail). You
			may need to retry a few times to see if the process will complete
			quicker
		</message>
		<moreinfo>SecurityInclusion</moreinfo>
		<module>Security</module>
	</scan>
	<scan id="20005">
		<regex>.*Basic::Set - Setting node /d* to level .*</regex>
		<type>Info</type>
		<message>Your Application set a value when OpenZWave was still
			starting up. There might be a delay between setting the value and the
			device actually receiving the command. Please read the MoreInfo Link
			for further details
		</message>
		<moreinfo>SlowResponseDuringStartup</moreinfo>
		<module>StartupTracking</module>
	</scan>
	<scan id="20006">
		<regex>.*Configuration::Set - Parameter=/d*, Value=/d* Size=/d*
		</regex>
		<type>Info</type>
		<message>Your Application set a value when OpenZWave was still
			starting up. There might be a delay between setting the value and the
			device actually receiving the command. Please read the MoreInfo Link
			for further details
		</message>
		<moreinfo>SlowResponseDuringStartup</moreinfo>
		<module>StartupTracking</module>
	</scan>
	<scan id="20007">
		<regex>.*Value_Lock::Set - Requesting lock to be .*</regex>
		<type>Info</type>
		<message>Your Application set a value when OpenZWave was still
			starting up. There might be a delay between setting the value and the
			device actually receiving the command. Please read the MoreInfo Link
			for further details
		</message>
		<moreinfo>SlowResponseDuringStartup</moreinfo>
		<module>StartupTracking</module>
	</scan>
	<scan id="20008">
		<regex>.*Value_Lock_Mode::Set - Requesting lock to be .*</regex>
		<type>Info</type>
		<message>Your Application set a value when OpenZWave was still
			starting up. There might be a delay between setting the value and the
			device actually receiving the command. Please read the MoreInfo Link
			for further details
		</message>
		<moreinfo>SlowResponseDuringStartup</moreinfo>
		<module>StartupTracking</module>
	</scan>
	<scan id="20009">
		<regex>.*Indicator::SetValue - Setting indicator to /d*</regex>
		<type>Info</type>
		<message>Your Application set a value when OpenZWave was still
			starting up. There might be a delay between setting the value and the
			device actually receiving the command. Please read the MoreInfo Link
			for further details
		</message>
		<moreinfo>SlowResponseDuringStartup</moreinfo>
		<module>StartupTracking</module>
	</scan>
	<!-- This one is fairly common 
	<scan id="20010"> <regex>.*NoOperation::Set 
		- Routing=.*</regex> <type>Info</type> <message>Your Application set a value 
		when OpenZWave was still starting up. There might be a delay between setting 
		the value and the device actually receiving the command. Please read the 
		MoreInfo Link for further details </message> <moreinfo>SlowResponseDuringStartup</moreinfo> 
		<module>StartupTracking</module> </scan> 
		-->
	<scan id="20011">
		<regex>.*NodeNaming::Set - Naming to '.*'</regex>
		<type>Info</type>
		<message>Your Application set a value when OpenZWave was still
			starting up. There might be a delay between setting the value and the
			device actually receiving the command. Please read the MoreInfo Link
			for further details
		</message>
		<moreinfo>SlowResponseDuringStartup</moreinfo>
		<module>StartupTracking</module>
	</scan>
	<scan id="20012">
		<regex>.*NodeNaming::SetLocation - Setting location to '.*'</regex>
		<type>Info</type>
		<message>Your Application set a value when OpenZWave was still
			starting up. There might be a delay between setting the value and the
			device actually receiving the command. Please read the MoreInfo Link
			for further details
		</message>
		<moreinfo>SlowResponseDuringStartup</moreinfo>
		<module>StartupTracking</module>
	</scan>
	<scan id="20013">
		<regex>.*Protection::Set - Setting protection state to '.*'</regex>
		<type>Info</type>
		<message>Your Application set a value when OpenZWave was still
			starting up. There might be a delay between setting the value and the
			device actually receiving the command. Please read the MoreInfo Link
			for further details
		</message>
		<moreinfo>SlowResponseDuringStartup</moreinfo>
		<module>StartupTracking</module>
	</scan>
	<scan id="20014">
		<regex>.*SwitchAll::Set - .* on node /d*</regex>
		<type>Info</type>
		<message>Your Application set a value when OpenZWave was still
			starting up. There might be a delay between setting the value and the
			device actually receiving the command. Please read the MoreInfo Link
			for further details
		</message>
		<moreinfo>SlowResponseDuringStartup</moreinfo>
		<module>StartupTracking</module>
	</scan>
	<scan id="20015">
		<regex>.*SwitchMultilevel::Set - Setting to level /d*</regex>
		<type>Info</type>
		<message>Your Application set a value when OpenZWave was still
			starting up. There might be a delay between setting the value and the
			device actually receiving the command. Please read the MoreInfo Link
			for further details
		</message>
		<moreinfo>SlowResponseDuringStartup</moreinfo>
		<module>StartupTracking</module>
	</scan>
	<scan id="20016">
		<regex>.*SwitchBinary::Set - Setting node /d* to .*</regex>
		<type>Info</type>
		<message>Your Application set a value when OpenZWave was still
			starting up. There might be a delay between setting the value and the
			device actually receiving the command. Please read the MoreInfo Link
			for further details
		</message>
		<moreinfo>SlowResponseDuringStartup</moreinfo>
		<module>StartupTracking</module>
	</scan>
	<scan id="20017">
		<regex>.*SwitchToggleBinary::Set - Toggling the state</regex>
		<type>Info</type>
		<message>Your Application set a value when OpenZWave was still
			starting up. There might be a delay between setting the value and the
			device actually receiving the command. Please read the MoreInfo Link
			for further details
		</message>
		<moreinfo>SlowResponseDuringStartup</moreinfo>
		<module>StartupTracking</module>
	</scan>
	<scan id="20018">
		<regex>.*SwitchToggleMultilevel::Set - Toggling the state</regex>
		<type>Info</type>
		<message>Your Application set a value when OpenZWave was still
			starting up. There might be a delay between setting the value and the
			device actually receiving the command. Please read the MoreInfo Link
			for further details
		</message>
		<moreinfo>SlowResponseDuringStartup</moreinfo>
		<module>StartupTracking</module>
	</scan>
	<scan id="20019">
		<regex>.*Value::Set - (.*) - (.*) - .* - .* - .*</regex>
		<type>Info</type>
		<message>Your Application set a value on ${1} (${2}) when OpenZWave was still
			starting up. There might be a delay between setting the value and the
			device actually receiving the command. Please read the MoreInfo Link
			for further details
		</message>
		<moreinfo>SlowResponseDuringStartup</moreinfo>
		<module>StartupTracking</module>
	</scan>


</statescanner>