forked from switchdoclabs/SDL_ESP32_OurWeather
-
Notifications
You must be signed in to change notification settings - Fork 0
/
SDL_Arduino_INA3221.h
95 lines (76 loc) · 4.17 KB
/
SDL_Arduino_INA3221.h
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
//
// SDL_Arduino_INA3221 Library
// SDL_Arduino_INA3221.cpp Arduino code - runs in continuous mode
// Version 1.2
// SwitchDoc Labs September 2019
//
//
/**************************************************************************/
/*!
Initial code from INA219 code (Basically just a core structure left)
@author K. Townsend (Adafruit Industries)
@license BSD (see BSDlicense.txt)
*/
/**************************************************************************/
#if ARDUINO >= 100
#include "Arduino.h"
#else
#include "WProgram.h"
#endif
#include <Wire.h>
/*=========================================================================
I2C ADDRESS/BITS
-----------------------------------------------------------------------*/
#define INA3221_ADDRESS (0x40) // 1000000 (A0+A1=GND)
#define INA3221_READ (0x01)
/*=========================================================================*/
/*=========================================================================
CONFIG REGISTER (R/W)
-----------------------------------------------------------------------*/
#define INA3221_REG_CONFIG (0x00)
/*---------------------------------------------------------------------*/
#define INA3221_CONFIG_RESET (0x8000) // Reset Bit
#define INA3221_CONFIG_ENABLE_CHAN1 (0x4000) // Enable Channel 1
#define INA3221_CONFIG_ENABLE_CHAN2 (0x2000) // Enable Channel 2
#define INA3221_CONFIG_ENABLE_CHAN3 (0x1000) // Enable Channel 3
#define INA3221_CONFIG_AVG2 (0x0800) // AVG Samples Bit 2 - See table 3 spec
#define INA3221_CONFIG_AVG1 (0x0400) // AVG Samples Bit 1 - See table 3 spec
#define INA3221_CONFIG_AVG0 (0x0200) // AVG Samples Bit 0 - See table 3 spec
#define INA3221_CONFIG_VBUS_CT2 (0x0100) // VBUS bit 2 Conversion time - See table 4 spec
#define INA3221_CONFIG_VBUS_CT1 (0x0080) // VBUS bit 1 Conversion time - See table 4 spec
#define INA3221_CONFIG_VBUS_CT0 (0x0040) // VBUS bit 0 Conversion time - See table 4 spec
#define INA3221_CONFIG_VSH_CT2 (0x0020) // Vshunt bit 2 Conversion time - See table 5 spec
#define INA3221_CONFIG_VSH_CT1 (0x0010) // Vshunt bit 1 Conversion time - See table 5 spec
#define INA3221_CONFIG_VSH_CT0 (0x0008) // Vshunt bit 0 Conversion time - See table 5 spec
#define INA3221_CONFIG_MODE_2 (0x0004) // Operating Mode bit 2 - See table 6 spec
#define INA3221_CONFIG_MODE_1 (0x0002) // Operating Mode bit 1 - See table 6 spec
#define INA3221_CONFIG_MODE_0 (0x0001) // Operating Mode bit 0 - See table 6 spec
/*=========================================================================*/
/*=========================================================================
SHUNT VOLTAGE REGISTER (R)
-----------------------------------------------------------------------*/
#define INA3221_REG_SHUNTVOLTAGE_1 (0x01)
/*=========================================================================*/
/*=========================================================================
BUS VOLTAGE REGISTER (R)
-----------------------------------------------------------------------*/
#define INA3221_REG_BUSVOLTAGE_1 (0x02)
/*=========================================================================*/
#define SHUNT_RESISTOR_VALUE (0.1) // default shunt resistor value of 0.1 Ohm
class SDL_Arduino_INA3221 {
public:
SDL_Arduino_INA3221(uint8_t addr = INA3221_ADDRESS, float shuntresistor = SHUNT_RESISTOR_VALUE);
void begin(void);
float getBusVoltage_V(int channel);
float getShuntVoltage_mV(int channel);
float getCurrent_mA(int channel);
int getManufID();
int getDeviceID();
uint8_t INA3221_i2caddr;
float INA3221_shuntresistor;
void wireWriteRegister(uint8_t reg, uint16_t value);
void wireReadRegister(uint8_t reg, uint16_t *value);
void INA3221SetConfig(void);
int16_t getBusVoltage_raw(int channel);
int16_t getShuntVoltage_raw(int channel);
};