Intel and AMD Ryzen: This SEDutil fork includes support for intel and AMD Ryzen systems with SHA-512 password authentication
Note: This version of SEDutil is not compatible with SHA-1 versions of SEDutil
This software is Copyright 2014-2017 Bright Plaza Inc. [email protected]
This file is part of sedutil.
sedutil is free software: you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation, either version 3 of the License, or (at your option) any later version.
sedutil is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details.
You should have received a copy of the GNU General Public License along with sedutil. If not, see http://www.gnu.org/licenses/.
sedutil - The Drive Trust Alliance Self Encrypting Drive Utility
This program and it's accompanying Pre-Boot Authorization image allow you to enable the locking in SED's that comply with the TCG OPAL 2.00 standard, Opalite, Pyrite, and Ruby.
You must be administrator/root to run the host managment program
In Linux libata.allow_tpm must be set to 1. Either via adding libata.allow_tpm=1 to the kernel flags at boot time or changing the contents of /sys/module/libata/parameters/allow_tpm from a "0" to a "1" on a running system.
***** sleep (S3) is not supported.
Orginal source code is available on GitHub at https://github.com/Drive-Trust-Alliance/sedutil
Linux and Windows executables and Linux PBA bootloader images for this version of SEDutil are available at https://github.com/ChubbyAnt/sedutil/releases
DTA sedutil: For AMD Ryzen Systems
The sedutil project provides a CLI tool (sedutil-cli) capable of setting up and managing self encrypting drives (SEDs) that comply with the TCG OPAL 2.00 standard, Opalite, Pyrite, and Ruby. This project also provides a pre-boot authentication image (linuxpba) which can be loaded onto an encrypted disk's shadow MBR. This pre-boot authentication image allows the user enter their password and unlock SED drives during the boot process. Using this tool can make data on the drive inaccessible!
To configure a drive, load a compatible RECOVERY image onto a USB drive and follow the instructions here:
https://github.com/Drive-Trust-Alliance/sedutil/wiki/Encrypting-your-drive
This version of sedutil is based off the original @dta implementation incorporating some modifications by @ladar, @ckamm and @CyrilVanErsche. This fork adds support for the PBA bootloader on AMD Ryzen and AMD Ryzen mobile systems.
Unique to this repo are the following modifications:
- SHA512 password hashing vs SHA1 on original SEDutil
- Compatibile with AMD Ryzen and AMD Ryzen mobile systems
Building is supported on Ubuntu 18.04.3 (LTS) x64. Other versions will probably not compile correctly!
To compile your own version of sedutil you will need the standard development tools, an internet connection, and ~10 GB of disk space.
sudo apt-get update && sudo apt-get upgrade -y
sudo apt-get install build-essential autoconf pkg-config libc6-dev make g++-multilib m4 libtool ncurses-dev unzip zip git python zlib1g-dev wget bsdmainutils automake curl bc rsync cpio git nasm -y
git clone https://github.com/ChubbyAnt/sedutil && cd sedutil && autoreconf --install && ./configure && make all && cd images && ./getresources && ./buildpbaroot && ./buildbios && ./buildUEFI64 && ./buildrescue Rescue32 && ./buildrescue Rescue64 && cd ..
git clone https://github.com/ChubbyAnt/sedutil
cd sedutil
autoreconf --install
./configure
make all
cd images
./getresources
./buildpbaroot
./buildbios
./buildUEFI64
./buildrescue Rescue32
./buildrescue Rescue64
cd ..
The various recovery and boot images will be located in the images directory.
This version has only been verified to boot on a HP x360 Envy AMD 3700u with a Samsung EVO 970 Plus 2TB NVMe drive. Testing has also focused only on the 64 bit UEFI images. While the other variants might work, you should exercise caution, and if possible, test the release on a computer with data that is expendable.
For the most comprehensive information, review this first:
https://github.com/Drive-Trust-Alliance/sedutil/wiki/Encrypting-your-drive
Both the PBA and rescue systems use the us_english keyboard. This can cause issues when setting the password on your normal operating system if you use another keyboard mapping. To make sure the PBA recognizes your password you are encouraged to set up you drive from the rescue system as described on this page.
These are the instructions for modern UEFI NVME equipped systems using SEDutil OPAL, Opalite, Pyrite, and Ruby locking and unlocking utility as a windows pre-boot bootloader:
Download the rescue system for 64bit UEFI
- UEFI support currently requires that Secure Boot be turned off
Transfer the Rescue image to the USB stick with a program like Balena Etcher.
Restart your computer, enter the BIOS, and disable secure boot.
Note: Earlier versions of SEDutil also required BIOS enable of "legacy boot" or "CSM" or "Compatility Mode" - this is no longer required with this version of SEDutil.
Boot the USB thumb drive with the rescue system on it. You will see the Login prompt, enter "root" there is no password so you will get a root shell prompt.
Enter the command sedutil-cli --scan
Expected Output:
#sedutil-cli --scan
Scanning for Opal compliant disks
/dev/nvme0 2 Samsung SSD 960 EVO 250GB 2B7QCXE7
/dev/sda 2 Crucial_CT250MX200SSD1 MU04
/dev/sdb 12 Samsung SSD 850 EVO 500GB EMT01B6Q
/dev/sdc 2 ST500LT025-1DH142 0001SDM7
/dev/sdd 12 Samsung SSD 850 EVO 250GB EMT01B6Q
No more disks present ending scan
Verify that your drive has a 2 in the second column indicating OPAL 2 support. If it doesn't do not proceed, there is something that is preventing sedutil from supporting your drive. If you continue you may erase all of your data.
Enter the command linuxpba and use a pass-phrase of debug. If you don't use debug as the pass-phrase your system will reboot!
Expected Output:
#linuxpba
DTA LINUX Pre Boot Authorization
Please enter pass-phrase to unlock OPAL drives: *****
Scanning....
Drive /dev/nvme0 Samsung SSD 960 EVO 250GB is OPAL NOT LOCKED
Drive /dev/sda Crucial_CT250MX200SSD1 is OPAL NOT LOCKED
Drive /dev/sdb Samsung SSD 850 EVO 500GB is OPAL NOT LOCKED
Drive /dev/sdc ST500LT025-1DH142 is OPAL NOT LOCKED
Drive /dev/sdd Samsung SSD 850 EVO 250GB is OPAL NOT LOCKED
Verify that Your drive is listed and the that the PBA reports it as "is OPAL"
Issuing the commands in the steps that follow will enable OPAL locking. If you have a problem you will need to follow the steps at the end of this page Recovery Information to either disable or remove OPAL locking.
The following steps use /dev/nvme0 as the device and UEFI64-1.15.img.gz for the PBA image, substitute the proper /dev/nvme? for your drive and the proper PBA name for your system
###Enable Locking and the PBA
Enter the commands below: (Use the password of debug for this test, it will be changed later)
gunzip /usr/sedutil/UEFI64-*img.gz
sedutil-cli --initialsetup debug /dev/nvme0
sedutil-cli --enablelockingrange 0 debug /dev/nvme0
sedutil-cli --setlockingrange 0 lk debug /dev/nvme0
sedutil-cli --setmbrdone off debug /dev/nvme0
sedutil-cli --loadpbaimage debug /usr/sedutil/UEFI64-*.img /dev/nvme0
Expected Output:
#sedutil-cli --initialsetup debug /dev/nvme0
- 14:06:39.709 INFO: takeOwnership complete
- 14:06:41.703 INFO: Locking SP Activate Complete
- 14:06:42.317 INFO: LockingRange0 disabled
- 14:06:42.694 INFO: LockingRange0 set to RW
- 14:06:43.171 INFO: MBRDone set on
- 14:06:43.515 INFO: MBRDone set on
- 14:06:43.904 INFO: MBREnable set on
- 14:06:43.904 INFO: Initial setup of TPer complete on /dev/nvme0
#sedutil-cli --enablelockingrange 0 debug /dev/nvme0
- 14:07:24.914 INFO: LockingRange0 enabled ReadLocking,WriteLocking
#sedutil-cli --setlockingrange 0 lk debug /dev/nvme0
- 14:07:46.728 INFO: LockingRange0 set to LK
#sedutil-cli --setmbrdone off debug /dev/nvme0
- 14:08:21.999 INFO: MBRDone set off
#gunzip /usr/sedutil/UEFI64-1.15.img.gz
#sedutil-cli --loadpbaimage debug /usr/sedutil/UEFI64-1.15.img /dev/nvme0
- 14:10:55.328 INFO: Writing PBA to /dev/nvme0
33554432 of 33554432 100% blk=1500
- 14:14:04.499 INFO: PBA image /usr/sedutil/UEFI64.img written to /dev/nvme0
#
Enter the command linuxpba and use a pass-phrase of debug
This second test will verify that your drive really does get unlocked.
Expected Output:
#linuxpba
DTA LINUX Pre Boot Authorization
Please enter pass-phrase to unlock OPAL drives: *****
Scanning....
Drive /dev/nvme0 Samsung SSD 960 EVO 250GB is OPAL Unlocked <--- IMPORTANT!!
Drive /dev/sda Crucial_CT250MX200SSD1 is OPAL NOT LOCKED
Drive /dev/sdb Samsung SSD 850 EVO 500GB is OPAL NOT LOCKED
Drive /dev/sdc ST500LT025-1DH142 is OPAL NOT LOCKED
Drive /dev/sdd Samsung SSD 850 EVO 250GB is OPAL NOT LOCKED
Verify that the PBA unlocks your drive, it should say "is OPAL Unlocked" If it doesn't then you will need to follow the steps at the end of this page to either remove OPAL or disable locking.
#Set a real password
The SID and Admin1 passwords do not have to match but it makes things easier.
edutil-cli --setsidpassword debug yourrealpassword /dev/nvme0
sedutil-cli --setadmin1pwd debug yourrealpassword /dev/nvme0
Expected Output:
#sedutil-cli --setsidpassword debug yourrealpassword /dev/nvme0
#sedutil-cli --setadmin1pwd debug yourrealpassword /dev/nvme0
- 14:20:53.352 INFO: Admin1 password changed
Make sure you didn't mistype your password by testing it.
sedutil-cli --setmbrdone on yourrealpassword /dev/nvme0
Expected Output:
#sedutil-cli --setmbrdone on yourrealpassword /dev/nvme0
- 14:22:21.590 INFO: MBRDone set on
Your drive is now using OPAL locking.
You now need to COMPLETELY POWER DOWN YOUR SYSTEM
This will lock the drive so that when you restart your system it will boot the PBA.
If there is an issue after enabling locking you can either disable locking or remove OPAL to continue using your drive without locking.
If you want to disable Locking and the PBA:
sedutil-cli -–disableLockingRange 0 <password> <drive>
sedutil-cli –-setMBREnable off <password> <drive>
Expected Output:
#sedutil-cli --disablelockingrange 0 debug /dev/nvme0
- 14:07:24.914 INFO: LockingRange0 disabled
#sedutil-cli --setmbrenable off debug /dev/nvme0
- 14:08:21.999 INFO: MBREnable set off
You can re-enable locking and the PBA using this command sequence:
sedutil-cli -–enableLockingRange 0 <password> <drive>
sedutil-cli –-setMBREnable on <password> <drive>
Expected Output:
#sedutil-cli --enablelockingrange 0 debug /dev/nvme0
- 14:07:24.914 INFO: LockingRange0 enabled ReadLocking,WriteLocking
#sedutil-cli --setmbrenable on debug /dev/nvme0
- 14:08:21.999 INFO: MBREnable set on
Some OPAL drives have a firmware bug that will erase all of your data if you issue the commands below. See Remove OPAL for a list of drive/firmware pairs that is know to have been tested.
sedutil-cli --revertnoerase <password> <drive>
Expected Output:
#sedutil-cli --revertnoerase debug /dev/nvme0
- 14:22:47.060 INFO: Revert LockingSP complete
Verify that the locking SP has been deactivated:
sedutil-cli --query {drive}
Look at the query output and make certain that the Locking section shows lockingEnabled=N
-----
Locking function (0x0002)
Locked = N, LockingEnabled = N, LockingSupported = Y,
---------
If the query does not show lockingEnabled=N DO NOT CONTINUE with the next step, if you do all your data will be erased.
Remove OPAL:
sedutil-cli --reverttper {SIDpassword} {drive}
Expected output:
#sedutil-cli --reverttper debug /dev/nvme0
- 14:23:13.968 INFO: revertTper completed successfully
#
When this is finished the drive will be in a non-opal managed state. This would allow you to do anything that you could have done before starting OPAL management under OPAL. You can also reinitiate OPAL management if you wish.