forked from networkupstools/nut
-
Notifications
You must be signed in to change notification settings - Fork 0
/
INSTALL.nut
341 lines (229 loc) · 10.5 KB
/
INSTALL.nut
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
Installation instructions
=========================
This chapter describe the various methods for installing Network UPS Tools.
Whenever it is possible, prefer <<Installing_packages, installing from packages>>.
Packagers have done an excellent and hard work at improving NUT integration into
their system.
[[Installing_source]]
Installing from source
----------------------
These are the essential steps for compiling and installing this software.
The NUT linkdoc:packager-guide[Packager Guide], which presents the best
practices for installing and integrating NUT, is also a good reading.
[NOTE]
.Keep in mind that...
================================================================================
- the paths shown below are the default values you get by just calling
configure by itself. If you have used --prefix or similar, things will be
different. Also, if you didn't install this program from source yourself, the
paths will probably have a number of differences.
- by default, your system probably won't find the man pages, since they
install to /usr/local/ups/man. You can fix this by editing your MANPATH, or
just do this:
man -M /usr/local/ups/man <man page>
- if your favorite system offers up to date binary packages, you should always
prefer these over a source installation. Along with the known advantages of such
systems for installation, upgrade and removal, there are many integration issues
that have been addressed.
================================================================================
Prepare your system
~~~~~~~~~~~~~~~~~~~~
System User creation
^^^^^^^^^^^^^^^^^^^^
Create at least one system user and a group for running this software. You
might call them "ups" and "nut". The exact names aren't important as
long as you are consistent.
The process for doing this varies from one system to the next, and
explaining how to add users is beyond the scope of this document.
For the purposes of this document, the user name and group name
will be 'ups' and 'nut' respectively.
Be sure the new user is a member of the new group! If you forget to
do this, you will have problems later on when you try to start upsd.
Build and install
~~~~~~~~~~~~~~~~~
[[Configuration]]
Configuration
^^^^^^^^^^^^^
Configure the source tree for your system. Add the '--with-user' and
'--with-group' switch to set the user name and group that you created
above.
./configure --with-user=ups --with-group=nut
If you need any other switches for configure, add them here. For example:
* to build and install USB drivers, add '--with-usb' (note that you
need to install libusb development package or files).
* to build and install SNMP drivers, add '--with-snmp' (note that
you need to install libsnmp development package or files).
* to build and install CGI scripts, add '--with-cgi'.
See <<Configure_options,Configure options>> from the User Manual,
docs/configure.txt or './configure --help' for all the available
options.
If you alter paths with additional switches, be sure to use those
new paths while reading the rest of the steps.
Reference: <<Configure_options,Configure options>> from the
User Manual.
Build the programs
^^^^^^^^^^^^^^^^^^
make
This will build the NUT client and server programs and the
selected drivers. It will also build any other features that were
selected during <<Configuration,configuration>> step above.
Installation
^^^^^^^^^^^^
[NOTE]
=====================================================================
you should now gain privileges for installing software if necessary:
su
=====================================================================
Install the files to a system level directory:
make install
This will install the compiled programs and man pages, as well as
some data files required by NUT. Any optional features selected
during configuration will also be installed.
This will also install sample versions of the NUT configuration
files. Sample files are installed with names like ups.conf.sample
so they will not overwrite any existing real config files you may
have created.
If you are packaging this software, then you will probably want to
use the DESTDIR variable to redirect the build into another place,
i.e.:
make DESTDIR=/tmp/package install
make DESTDIR=/tmp/package install-conf
[[StatePath]]
State path creation
^^^^^^^^^^^^^^^^^^^
Create the state path directory for the driver(s) and server to use
for storing UPS status data and other auxiliary files, and make it
group-writable by the group of the system user you created.
mkdir -p /var/state/ups
chmod 0770 /var/state/ups
chown root:nut /var/state/ups
[[Ownership]]
Ownership and permissions
^^^^^^^^^^^^^^^^^^^^^^^^^
Set ownership data and permissions on your serial or USB ports
that go to your UPS hardware. Be sure to limit access to just
the user you created earlier.
These examples assume the second serial port (ttyS1) on a typical
Slackware system. On FreeBSD, that would be cuaa1. Serial ports
vary greatly, so yours may be called something else.
chmod 0660 /dev/ttyS1
chown root:nut /dev/ttyS1
////////////////////////////////////////////////////////////////////////////////
FIXME: TBR
////////////////////////////////////////////////////////////////////////////////
The setup for USB ports is slightly more complicated. Device files
for USB devices, such as /proc/bus/usb/002/001, are usually
created "on the fly" when a device is plugged in, and disappear
when the device is disconnected. Moreover, the names of these
device files can change randomly. To set up the correct
permissions for the USB device, you may need to set up (operating
system dependent) hotplugging scripts. Sample scripts and
information are provided in the scripts/hotplug and
scripts/udev directories. For most users, the hotplugging scripts
will be installed automatically by "make install".
(If you want to try if a driver works without setting up
hotplugging, you can add the "-u root" option to upsd, upsmon, and
drivers; this should allow you to follow the below
instructions. However, don't forget to set up the correct
permissions later!).
NOTE: if you are using something like udev or devd, make sure
these permissions stay set across a reboot. If they revert to the
old values, your drivers may fail to start.
You are now ready to configure NUT, and start testing and using it.
You can jump directly to the <<Configuration_notes,NUT configuration>>.
[[Installing_packages]]
Installing from packages
------------------------
This chapter describes the specific installation steps when using
binary packages that exist on various major systems.
[[Debian]]
Debian, Ubuntu and other derivatives
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
NOTE: NUT is packaged and well maintained in these systems.
The official Debian packager is part of the NUT Team.
Using your preferred method (apt-get, aptitude, Synaptic, ...), install
the 'nut' package, and optionally the following:
- 'nut-cgi', if you need the CGI (HTML) option,
- 'nut-snmp', if you need the snmp-ups driver,
- 'nut-xml', for the netxml-ups driver,
- 'nut-powerman-pdu', to control the PowerMan daemon (PDU management)
- 'nut-dev', if you need the development files.
////////////////////////////////////////////////////////////////////////////////
- nut-client
////////////////////////////////////////////////////////////////////////////////
Configuration files are located in /etc/nut.
linkman:nut.conf[5] must be edited to be able to invoke /etc/init.d/nut
NOTE: Ubuntu users can access the APT URL installation by clicking on link:apt://nut[this link].
[[Mandriva]]
Mandriva
~~~~~~~~
NOTE: NUT is packaged and well maintained in these systems.
The official Mandriva packager is part of the NUT Team.
Using your preferred method (urpmi, RPMdrake, ...), install one of the two below
packages:
- 'nut-server' if you have a 'standalone' or 'netserver' installation,
- 'nut' if you have a 'netclient' installation.
Optionally, you can also install the following:
- 'nut-cgi', if you need the CGI (HTML) option,
- 'nut-devel', if you need the development files.
[[SUSE]]
SUSE / openSUSE
~~~~~~~~~~~~~~~
NOTE: NUT is packaged and well maintained in these systems.
The official SUSE packager is part of the NUT Team.
Install the 'nut-classic' package, and optionally the following:
- 'nut-drivers-net', if you need the snmp-ups or the netxml-ups drivers,
- 'nut-cgi', if you need the CGI (HTML) option,
- 'nut-devel', if you need the development files,
NOTE: SUSE and openSUSE users can use the
link:http://software.opensuse.org/search?baseproject=ALL&p=1&q=nut[one-click install method]
to install NUT.
[[RedHat]]
Red Hat, Fedora and CentOS
~~~~~~~~~~~~~~~~~~~~~~~~~~
NOTE: NUT is packaged and well maintained in these systems.
The official Red Hat packager is part of the NUT Team.
Using your preferred method (yum, Add/Remove Software, ...), install one of the
two below packages:
- 'nut' if you have a 'standalone' or 'netserver' installation,
- 'nut-client' if you have a 'netclient' installation.
Optionally, you can also install the following:
- 'nut-cgi', if you need the CGI (HTML) option,
- 'nut-xml', if you need the netxml-ups driver,
- 'nut-devel', if you need the development files.
[[FreeBSD]]
FreeBSD
~~~~~~~
You can either install NUT as a binary package or as a port.
Binary package
^^^^^^^^^^^^^^
To install NUT as a package execute:
# pkg install nut
Port
^^^^
The port is located under +sysutils/nut+.
Use +make config+ to select configuration options, e.g. to build the optional CGI scripts.
To install it, use:
# make install clean
USB UPS on FreeBSD
^^^^^^^^^^^^^^^^^^
For USB UPS devices the NUT package/port installs devd rules in +/usr/local/etc/devd/nut-usb.conf+ to set USB device permissions. 'devd' needs to be restarted for these rules to apply:
# service devd restart
(Re-)connect the device after restarting 'devd' and check that the USB device has the proper
permissions. Check the last entries of the system message buffer. You should
find an entry like
# dmesg | tail
[...]
ugen0.2: <INNO TECH USB to Serial> at usbus0
The device file must be owned by group +uucp+ and must be group
read-/writable. In the example from above this would be
# ls -Ll /dev/ugen0.2
crw-rw---- 1 root uucp 0xa5 Mar 12 10:33 /dev/ugen0.2
If the permissions are not correct, verify that your device is registered in
+/usr/local/etc/devd/nut-usb.conf+. The vendor and product id can be found
using:
# usbconfig -u 0 -a 2 dump_device_desc
where +-u+ specifies the USB bus number and +-a+ specifies the USB device index.
You are now ready to configure NUT, and start testing and using it.
You can jump directly to the
<<Configuration_notes,NUT configuration>>.